You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Motor starting while flasing firmware by RSR » Sun, 2017-09-17 15:31 |
0 |
by RSR Sun, 2017-09-17 15:31 |
|
|
motor stops spinning on its own by rsarver » Tue, 2021-03-16 16:30 |
1 |
by rsarver Tue, 2021-03-16 22:13 |
|
|
Motor Stuck at 55% Duty Cycle by motion_sickness » Sun, 2021-11-14 16:47 |
1 |
by drdrs Sun, 2021-11-14 21:20 |
|
|
Motor temperature, how to set limit >120 C ? by RSR » Wed, 2018-08-22 12:40 |
3 |
by Danny Bokma Thu, 2018-08-23 07:19 |
|
|
motor to slow and no power by Thiery Vardon » Sat, 2021-01-09 10:45 |
2 |
by Thiery Vardon Tue, 2021-01-12 13:27 |
|
|
Motor whine with HFI? by christopher.h.poole » Mon, 2021-04-19 15:49 |
2 |
by christopher.h.poole Tue, 2021-06-15 21:18 |
|
|
Motor wizard settings by ESCam » Thu, 2018-11-08 22:49 |
8 |
by dtp Mon, 2023-11-20 00:49 |
|
|
Motors spin up during detection but then won't move by jordan314 » Thu, 2019-02-21 09:18 |
12 |
by KDoc Tue, 2023-01-17 00:13 |
|
|
Motors wont turn independently by huffauden19 » Mon, 2020-11-30 06:24 |
0 |
by huffauden19 Mon, 2020-11-30 06:24 |
|
|
Multiple VESC's in duty cycle mode by Rudolf10000 » Sat, 2019-04-20 13:24 |
1 |
by Rudolf10000 Mon, 2019-04-29 19:34 |
|
|
Need Help Setting Up Dual VESC on Trampa by MIKEtheBIKE » Wed, 2020-09-09 03:15 |
0 |
by MIKEtheBIKE Wed, 2020-09-09 03:15 |
|
|
Need help: encoder shows 9.6 rotations per 1 motor rotation (9.6:1 gearbox) by Alico » Thu, 2025-12-11 14:41 |
0 |
by Alico Thu, 2025-12-11 14:41 |
|
|
New version. by ThierryGTLTS » Thu, 2017-09-07 19:22 |
6 |
by Hectortcher Wed, 2020-03-04 11:21 |
|
|
Newbie question : How to switch to RPM mode ? by Lezard » Thu, 2024-02-29 19:30 |
1 |
by Lezard Mon, 2024-03-11 15:18 |
|
|
No brakes in PID Speed Control mode by karololo » Tue, 2019-10-15 11:31 |
3 |
by Gesndrery Thu, 2019-12-26 07:00 |
|
|
no effect on set erpm/speed limit by xenon321 » Sat, 2021-04-24 20:43 |
0 |
by xenon321 Sun, 2021-04-25 16:53 |
|
|
No Single Direction ADC in FW v6.06??? by rcalicea » Fri, 2026-02-13 09:15 |
0 |
by rcalicea Fri, 2026-02-13 09:23 |
|
|
Noobs need to update and / or configure old VESC 4.12 by Loops » Tue, 2023-02-07 11:49 |
0 |
by Loops Tue, 2023-02-07 11:49 |
|
|
Not responding to the throttle when moving backwards by jprojpro » Fri, 2022-07-15 15:30 |
3 |
by mannerz91 Mon, 2024-08-05 22:23 |
|
|
Not sure if parameter update in VESC tool works by srinath » Thu, 2023-06-08 11:29 |
0 |
by srinath Thu, 2023-06-08 11:29 |
|
|
Not sure what motor weight to choose in VESC Tool Setup Wizard by edvin » Mon, 2024-06-24 13:28 |
0 |
by edvin Mon, 2024-06-24 13:28 |
|
|
NRF connection error by Denn » Wed, 2022-02-02 11:17 |
0 |
by Denn Wed, 2022-02-02 11:17 |
|
|
Nrf connection error by vufmihai » Sat, 2020-04-25 22:00 |
0 |
by vufmihai Sat, 2020-04-25 22:00 |
|
|
NRF5X SWD Prog detection broken, always detects NRF52832 512K/64K by zippy » Sun, 2021-06-06 16:19 |
1 |
by zippy Sun, 2021-06-06 17:58 |
|
|
NVIDIA Jetson AGX Outputting PWM to Flipsky VESC Issue by colemalinchock » Tue, 2025-01-14 00:40 |
0 |
by colemalinchock Tue, 2025-01-14 00:40 |
Log in to post new content in the forum.
