You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
PPM problems by rufr123 » Sat, 2020-10-31 20:49 |
1 |
by TheFallen Tue, 2020-11-03 00:29 |
|
|
Bug Report - Motor/App Data not saved to VESC by bb67 » Sun, 2020-06-21 10:26 |
1 |
by bb67 Sat, 2020-07-04 12:21 |
|
|
Determining Motor and Battery Current Max by technique » Tue, 2020-07-14 15:03 |
1 |
by probie Wed, 2020-08-26 22:01 |
|
|
How to set dead time on BLDC mode? by AllenFF » Wed, 2020-04-15 05:48 |
1 |
by hexakopter Sat, 2020-04-18 16:30 |
|
|
PPM Pulselength mapping by Shaftdriver » Tue, 2022-10-04 19:50 |
1 |
by skyline1970 Thu, 2022-11-24 20:15 |
|
|
Data log field value detailed descriptions by Foilguy » Mon, 2023-06-12 20:59 |
1 |
by Foilguy Wed, 2023-06-14 16:12 |
|
|
Vesc Tool Use For Adjusting Black Tip DPV HELP NEEDED by Rsapple » Sun, 2023-08-13 13:37 |
1 |
by Rsapple Sun, 2023-08-13 14:13 |
|
|
Position control without encoder by bearing » Tue, 2023-04-04 18:45 |
1 |
by bearing Thu, 2023-04-06 22:07 |
|
|
Sailboat regen by flydr2 » Wed, 2023-04-12 20:10 |
1 |
by vadicus Wed, 2023-05-10 20:06 |
|
|
Problem to configure my esc with PWM-signal by Lucar » Wed, 2022-09-14 10:05 |
1 |
by skyline1970 Thu, 2022-11-24 20:26 |
|
|
Flipsky nrf51288 by Idoff » Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
|
|
Is there a complete documentation for the communication protocol between the vesc tool and the board? by aishangmu » Tue, 2018-12-25 09:00 |
2 |
by Caustic_Zinc Fri, 2019-02-08 19:27 |
|
|
Autodetection algorithm by Griffen » Thu, 2019-01-03 18:44 |
2 |
by Gmack Fri, 2020-09-18 16:39 |
|
|
cant connect via usb by curtm » Wed, 2019-06-19 03:05 |
2 |
by curtm Thu, 2019-07-04 00:37 |
|
|
Fault Codes by Joe_Lowtech » Wed, 2019-02-13 20:06 |
2 |
by mthielvoldt Thu, 2019-07-18 00:38 |
|
|
Advanced settings for FOC motor detection (flux linkage) by jaghori.sasan » Sun, 2019-02-17 09:34 |
2 |
by jaghori.sasan Sun, 2019-02-17 17:51 |
|
|
"bad detection result received" impossible to achieved motor detection ! by titimomotete » Wed, 2019-03-20 17:21 |
2 |
by doom Mon, 2019-08-05 10:52 |
|
|
VESC Tool 0.95 App by einbi » Tue, 2018-10-09 11:02 |
2 |
by Yanick Hautecoeur Thu, 2021-09-30 13:55 |
|
|
Motor setup help please by TrevM » Wed, 2017-12-13 17:11 |
2 |
by nickw1881 Wed, 2018-03-21 05:42 |
|
|
VESC Tool RPM not the actual in real life by Poh Boon pin » Sun, 2021-07-11 16:00 |
2 |
by hoeken Wed, 2021-09-01 15:56 |
|
|
RPM increase by Tibor Kalman Za... » Tue, 2021-02-23 10:12 |
2 |
by Tibor Kalman Za... Sat, 2021-02-27 21:41 |
|
|
motor max rpm and current severely limited? by Roy Zhang » Mon, 2021-08-09 19:23 |
2 |
by vadicus Thu, 2021-08-12 04:06 |
|
|
Update 0.87 impossible by vpower » Thu, 2018-01-18 13:17 |
2 |
by arvidb Thu, 2018-01-18 17:07 |
|
|
Overheating protection, voltage-/current-limitation etc. by kianK » Thu, 2021-04-15 07:23 |
2 |
by lilliamhoyle Wed, 2021-07-07 09:36 |
|
|
ADC Connector is very touchy by ebikerevolution » Wed, 2018-05-09 20:30 |
2 |
by TechAUmNu Tue, 2018-05-15 10:46 |
Log in to post new content in the forum.
