You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Vesc doesn't react to can messages from PC by BorisDeroo » Fri, 2021-12-17 16:54 |
1 |
by yuri12 Wed, 2022-02-09 17:33 |
|
|
Vesc can't connect to vesc tool by Roansky1 » Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
|
|
VESC 75/300 Configuration problems with Hacker Q80 Motors by electricfox » Thu, 2019-02-28 18:23 |
13 |
by Cherry Tue, 2021-01-12 11:56 |
|
|
VESC 75/300 Configuration of 7kg Innerrunner Surron by electricfox » Thu, 2019-05-16 18:38 |
15 |
by Armond Ohan Mon, 2020-12-21 06:34 |
|
|
VESC 6.05 Fault Coded under Voltage by amblerev » Tue, 2024-07-23 14:37 |
0 |
by amblerev Tue, 2024-07-23 14:37 |
|
|
Vesc 6, FW 5.1, WH charged is not being logged by BalorNG » Thu, 2020-12-03 14:19 |
0 |
by BalorNG Thu, 2020-12-03 14:19 |
|
|
VESC 6 beta + mobile app by doh » Sat, 2024-04-06 19:16 |
0 |
by doh Sat, 2024-04-06 19:16 |
|
|
VESC 4.12 - Current limited at 100A by Laerson » Sun, 2019-09-08 20:23 |
1 |
by benjamin Mon, 2019-09-09 18:20 |
|
|
Vesc 1.26 BLE Scan error by huzaini » Mon, 2019-12-16 17:17 |
8 |
by sirAnton Sun, 2020-08-09 15:55 |
|
|
Very low Flux Linkage calulation FOC,General Tab - 0.0xx mWb by kjjajsdASHD » Sun, 2025-02-02 13:59 |
0 |
by kjjajsdASHD Sun, 2025-02-02 13:59 |
|
|
version of Vesc Tool for Flipsky 6.6 by Robert Adkins » Sun, 2019-09-29 18:13 |
3 |
by frank Wed, 2019-10-23 09:35 |
|
|
Version 3.01 destroyed version 2.06 too by Knaubel » Sun, 2022-05-15 21:23 |
6 |
by Knaubel Wed, 2022-05-18 16:16 |
|
|
Version 2.03 won't open by marialoise » Fri, 2020-03-13 20:24 |
5 |
by pwilkinson91 Tue, 2023-06-27 22:07 |
|
|
Version 0.84, some problems with ADC, see 2nd post please! by ThierryGTLTS » Sun, 2017-10-29 14:11 |
3 |
by ThierryGTLTS Fri, 2017-11-03 16:56 |
|
|
Values truncated, but why? by oger » Tue, 2020-03-24 17:43 |
0 |
by oger Tue, 2020-03-24 17:43 |
|
|
Use Vesc-Tool to run two motors simultaneously via CAN by microlomaniac » Thu, 2021-06-17 11:55 |
2 |
by spacewalker Tue, 2021-06-22 08:23 |
|
|
Use sensors on the output shaft of a motor attached to a large gear ratio gearbox by davidq1688 » Wed, 2022-04-27 05:23 |
1 |
by tobiokanobi Thu, 2022-04-28 14:48 |
|
|
Use ADC2 as reverse button for ADC+UART/Current Reverse Button by jessejay356 » Mon, 2024-09-23 01:06 |
0 |
by jessejay356 Mon, 2024-09-23 01:06 |
|
|
USB-serial_no ports show up at all by Josiah Eberharter » Tue, 2024-07-23 05:45 |
0 |
by Josiah Eberharter Tue, 2024-07-23 05:45 |
|
|
USB command and ADC1 Throttle by JWilson » Fri, 2024-08-09 23:24 |
1 |
by electricfox Sun, 2024-08-25 12:05 |
|
|
Urgent Help Connecting TS5700N8501-like Magnetic Encoder by jumana » Tue, 2025-01-14 19:37 |
0 |
by jumana Tue, 2025-01-14 19:37 |
|
|
Upgrade the Bootloader? by erikfed » Tue, 2022-03-08 20:32 |
0 |
by erikfed Tue, 2022-03-08 20:32 |
|
|
Updating App and info xml failed by Pimousse » Tue, 2018-01-30 21:06 |
0 |
by Pimousse Tue, 2018-01-30 21:06 |
|
|
Updated Firmware on 2 New VESC's says firmware doesnt match when connected by CanBus Cable by vesserik » Mon, 2019-04-08 21:10 |
1 |
by dbell Tue, 2020-12-01 02:14 |
|
|
Update FW using vesc tool over phone by SkaterBoy58 » Thu, 2019-03-14 05:33 |
0 |
by SkaterBoy58 Thu, 2019-03-14 05:33 |
Log in to post new content in the forum.
