You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter![]() |
Replies | Last post | |
---|---|---|---|
ConfBackup, Where does it save it by mikemoy » Tue, 2021-09-07 16:25 |
1 |
by ndp Thu, 2022-05-12 20:25 |
|
Compiled Vesc Tool Won't Recognize Firmware - Windows 1.23 by KingRagnar22 » Wed, 2019-10-02 01:29 |
1 |
by a.dahhak Mon, 2021-02-01 16:54 |
|
Communication over UART or CAN by JCLNEIL » Wed, 2023-12-13 14:36 |
0 |
by JCLNEIL Wed, 2023-12-13 14:36 |
|
Command Line Options by Dude » Wed, 2017-10-18 22:56 |
6 |
by woodmastr Thu, 2022-07-21 14:23 |
|
Comm conflict when connecting external imu? by Lennart Duijn » Wed, 2023-05-31 22:53 |
0 |
by Lennart Duijn Wed, 2023-05-31 22:53 |
|
Combo VESC 75/300 and Scorpion 7455-320KV 22.4kW issue by Nexxor » Mon, 2022-05-30 19:45 |
16 |
by hansholzel24 Thu, 2024-06-13 13:13 |
|
Clicking File Location settings reset input configuration. Bug? by tiztrain » Mon, 2022-07-25 03:34 |
0 |
by tiztrain Mon, 2022-07-25 03:34 |
|
Changing Output Voltage frequency by davbams » Wed, 2019-07-24 21:20 |
1 |
by district9prawn Thu, 2019-07-25 02:59 |
|
Changing minimum duty cycle prevents VESC from connecting via USB while ADC throttle is connected by shimdidly » Sun, 2017-10-15 00:48 |
0 |
by shimdidly Sun, 2017-10-15 00:48 |
|
Change RT data to metric by dannydnl » Sun, 2023-10-29 16:55 |
0 |
by dannydnl Sun, 2023-10-29 16:55 |
|
Change HW after wrong Firmware Update by Hassi » Sun, 2017-10-01 15:46 |
4 |
by benjamin Sun, 2017-10-22 23:32 |
|
Can´t increase current by increase RPM by hubacek000 » Mon, 2021-09-13 13:22 |
1 |
by frank Tue, 2021-09-14 12:17 |
|
Cant copy data from CAN Debugger by testusernameimsorry » Sat, 2024-03-09 11:52 |
0 |
by testusernameimsorry Sat, 2024-03-09 11:52 |
|
cant connect via usb by curtm » Wed, 2019-06-19 03:05 |
2 |
by curtm Thu, 2019-07-04 00:37 |
|
Cannot get any PPM signals from Arduino. Or is it just the VESC tool? by MaxMaker1 » Thu, 2018-06-21 23:06 |
4 |
by tuloski Thu, 2018-09-13 09:36 |
|
Cannot connect to vesc tool app by sharpshooterjd » Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
|
Can't update the VESC firmware by mansolander » Thu, 2020-03-05 11:30 |
1 |
by mansolander Fri, 2020-03-06 11:24 |
|
Can't spin both motors over CAN-bus by Kokonenen » Wed, 2023-04-19 11:19 |
4 |
by mansi712 Wed, 2024-10-30 13:40 |
|
Can't get Dual drive/CAN bus working by Xadiant » Sun, 2019-09-22 20:49 |
11 |
by Kokonenen Wed, 2023-04-19 11:10 |
|
Can't find good parameters for FOC detection by Kabroc » Thu, 2020-04-30 16:28 |
0 |
by Kabroc Thu, 2020-04-30 16:28 |
|
Can the PPM mapping be changed so that higher duty cycle means slower speed? by UncleJoe » Mon, 2020-05-25 11:46 |
3 |
by UncleJoe Thu, 2020-11-19 15:06 |
|
Can I run duty sweep without laptop? by gavinremme » Tue, 2024-07-30 00:05 |
0 |
by gavinremme Tue, 2024-07-30 00:05 |
|
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed » Fri, 2019-08-02 20:00 |
0 |
by Munkyheed Fri, 2019-08-02 20:00 |
|
CAN bus support not enabled in this build of vesc tool? by Tsomo » Fri, 2021-10-01 09:48 |
18 |
by merten Fri, 2024-08-09 18:14 |
|
Calibration ERROR with TLE5012B Magnetic encoder in ABI mode by cejota » Fri, 2022-03-25 03:19 |
2 |
by XieMaster Mon, 2022-11-14 05:32 |
Log in to post new content in the forum.
