You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Sticky:
Step by Step Setup by frank » Wed, 2017-10-04 17:15 |
8 |
by mc Tue, 2018-02-20 11:12 |
|
|
Sticky:
Motor Values in VESC-Tool 2019 by frank » Wed, 2019-02-27 09:40 |
18 |
by Billy N Fri, 2021-03-26 07:22 |
|
|
Sticky:
FOC wizard confusion by Stupidspencer » Mon, 2019-07-08 04:18 |
4 |
by lurch Sun, 2021-10-24 14:46 |
|
|
Реверс вращения двигателя by Wolod5 » Sat, 2021-01-16 09:59 |
2 |
by Wolod5 Sat, 2021-01-16 12:21 |
|
|
[Solved] VESC Tool "could not deserialize motor configuration" with custom firmware by bsobeloffgittes » Fri, 2024-05-03 20:30 |
1 |
by Thimoty Brenden Fri, 2024-06-14 19:16 |
|
|
[SOLVED] RPM setting not working by olivierskypullc... » Wed, 2019-02-27 12:14 |
2 |
by olivierskypullc... Wed, 2019-03-06 10:10 |
|
|
[SOLVED] Compile vesc tool mobile apk by TZTZ » Mon, 2020-05-25 18:51 |
1 |
by TZTZ Mon, 2020-05-25 23:14 |
|
|
[SOLVED] Can I use ADC2 for main throttle control? by oschwartz10612 » Wed, 2021-12-01 22:38 |
3 |
by oschwartz10612 Fri, 2021-12-03 05:08 |
|
|
Yet another failed connection.... by MiguelXJ » Mon, 2024-01-01 19:28 |
0 |
by MiguelXJ Mon, 2024-01-01 19:28 |
|
|
Wrong Motor detection values after STM swap dual vesc 6 by Micro » Sun, 2019-08-18 01:59 |
0 |
by Micro Sun, 2019-08-18 02:14 |
|
|
Wrong HW version selected during FW update by babyboi » Sat, 2018-12-15 21:30 |
2 |
by babyboi Sat, 2018-12-22 03:55 |
|
|
Writing value to both VESCs on FocFox Unity by agraham » Wed, 2022-02-23 21:45 |
2 |
by benjamin Thu, 2022-02-24 10:57 |
|
|
Writing to slave vesc sometimes cause loss of can bus by meashman » Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
|
|
Write App Configuration via UART [SOLVED] by v8-rt » Mon, 2020-11-02 13:13 |
1 |
by Halas1941 Sun, 2020-11-29 14:04 |
|
|
Windows Bluetooth VESC 75/300 by Markula » Wed, 2019-11-06 17:33 |
1 |
by frank Fri, 2019-11-08 17:52 |
|
|
windows 7 VESC TOOL 1.25 wont open/not responding HELP PLEASE by timgoebel12@gma... » Tue, 2019-11-12 00:42 |
3 |
by yehsk8rz Sat, 2021-12-04 20:52 |
|
|
Windows 10 free tool wont open... by zip » Sun, 2024-06-30 07:09 |
2 |
by groove4life Mon, 2024-07-29 19:07 |
|
|
Wh/mi trip calculation error by devcic » Mon, 2024-03-11 16:44 |
0 |
by devcic Mon, 2024-03-11 16:44 |
|
|
Voltage measurement calibration? by pyryjansson » Tue, 2019-04-30 20:19 |
2 |
by frank Wed, 2022-11-30 09:55 |
|
|
Vesc_tool OVER_TEMP_FET by XIII » Thu, 2018-01-11 17:26 |
0 |
by XIII Thu, 2018-01-11 17:26 |
|
|
vesc_tool 6 and vesc 4.12 -> motor setup of small outrunner not working by Gawarmel » Thu, 2024-02-29 14:56 |
0 |
by Gawarmel Thu, 2024-02-29 14:56 |
|
|
Vesctool otg by meashman » Sat, 2022-08-06 10:05 |
2 |
by meashman Wed, 2022-08-17 06:39 |
|
|
VESCTOOL - Multiple VESC simultaneous configuration (Same CANBUS ID issues) by Filcas » Thu, 2021-02-18 20:52 |
2 |
by Filcas Fri, 2021-02-19 01:37 |
|
|
VESC100/250 - motor current setting ignored? by tobiokanobi » Mon, 2022-05-02 13:27 |
3 |
by frank Tue, 2022-05-03 20:54 |
|
|
Vesc-tool TCP Connection by nlabs » Fri, 2017-12-08 02:30 |
1 |
by milesf Fri, 2021-12-10 03:40 |
Log in to post new content in the forum.
