You are here

VESC Tool

Topic / Topic startersort descending Replies Last post
Normal topic UART write read arduino
by matiller » Sat, 2019-06-01 20:18
0
by matiller
Sat, 2019-06-01 20:18
Normal topic Unable to connect to vesc through can bus
by Kupofty » Thu, 2022-10-20 16:24
0
by Kupofty
Thu, 2022-10-20 16:24
Normal topic Understanding FOC Wizard Innerworkings
by gravity99 » Thu, 2022-08-18 22:24
2
by gravity99
Mon, 2022-08-22 15:23
Normal topic Unrecognized USB port vesc tool 1.25
by geotoine » Fri, 2019-11-08 15:35
1
by bb67
Fri, 2020-06-12 18:10
Normal topic Update 0.87 impossible
by vpower » Thu, 2018-01-18 13:17
2
by arvidb
Thu, 2018-01-18 17:07
Normal topic Update fail from FW3.58 to 3.61
by sachs2019 » Tue, 2019-09-10 15:51
7
by AlmaRaposa
Thu, 2021-03-11 17:44
Normal topic Update FW on multiple VESC pcbs using CAN issue
by Offline » Thu, 2021-05-20 07:36
0
by Offline
Thu, 2021-05-20 07:36
Normal topic Update FW using vesc tool over phone
by SkaterBoy58 » Thu, 2019-03-14 05:33
0
by SkaterBoy58
Thu, 2019-03-14 05:33
Normal topic Updated Firmware on 2 New VESC's says firmware doesnt match when connected by CanBus Cable
by vesserik » Mon, 2019-04-08 21:10
1
by dbell
Tue, 2020-12-01 02:14
Normal topic Updating App and info xml failed
by Pimousse » Tue, 2018-01-30 21:06
0
by Pimousse
Tue, 2018-01-30 21:06
Normal topic Upgrade the Bootloader?
by erikfed » Tue, 2022-03-08 20:32
0
by erikfed
Tue, 2022-03-08 20:32
Normal topic Use sensors on the output shaft of a motor attached to a large gear ratio gearbox
by davidq1688 » Wed, 2022-04-27 05:23
1
by tobiokanobi
Thu, 2022-04-28 14:48
Normal topic Use Vesc-Tool to run two motors simultaneously via CAN
by microlomaniac » Thu, 2021-06-17 11:55
2
by spacewalker
Tue, 2021-06-22 08:23
Normal topic Values truncated, but why?
by oger » Tue, 2020-03-24 17:43
0
by oger
Tue, 2020-03-24 17:43
Normal topic Version 0.84, some problems with ADC, see 2nd post please!
by ThierryGTLTS » Sun, 2017-10-29 14:11
3
by ThierryGTLTS
Fri, 2017-11-03 16:56
Normal topic Version 2.03 won't open
by marialoise » Fri, 2020-03-13 20:24
5
by pwilkinson91
Tue, 2023-06-27 22:07
Normal topic Version 3.01 destroyed version 2.06 too
by Knaubel » Sun, 2022-05-15 21:23
6
by Knaubel
Wed, 2022-05-18 16:16
Normal topic version of Vesc Tool for Flipsky 6.6
by Robert Adkins » Sun, 2019-09-29 18:13
3
by frank
Wed, 2019-10-23 09:35
Normal topic Vesc 1.26 BLE Scan error
by huzaini » Mon, 2019-12-16 17:17
8
by sirAnton
Sun, 2020-08-09 15:55
Normal topic VESC 4.12 - Current limited at 100A
by Laerson » Sun, 2019-09-08 20:23
1
by benjamin
Mon, 2019-09-09 18:20
Normal topic Vesc 6, FW 5.1, WH charged is not being logged
by BalorNG » Thu, 2020-12-03 14:19
0
by BalorNG
Thu, 2020-12-03 14:19
Hot topic VESC 75/300 Configuration of 7kg Innerrunner Surron
by electricfox » Thu, 2019-05-16 18:38
15
by Armond Ohan
Mon, 2020-12-21 06:34
Normal topic VESC 75/300 Configuration problems with Hacker Q80 Motors
by electricfox » Thu, 2019-02-28 18:23
13
by Cherry
Tue, 2021-01-12 11:56
Normal topic Vesc can't connect to vesc tool
by Roansky1 » Sat, 2022-04-30 13:05
3
by frank
Tue, 2022-05-03 20:52
Normal topic Vesc doesn't react to can messages from PC
by BorisDeroo » Fri, 2021-12-17 16:54
1
by yuri12
Wed, 2022-02-09 17:33
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - VESC Tool