You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Motors spin up during detection but then won't move by jordan314 » Thu, 2019-02-21 09:18 |
12 |
by KDoc Tue, 2023-01-17 00:13 |
|
|
Motors wont turn independently by huffauden19 » Mon, 2020-11-30 06:24 |
0 |
by huffauden19 Mon, 2020-11-30 06:24 |
|
|
Multiple VESC's in duty cycle mode by Rudolf10000 » Sat, 2019-04-20 13:24 |
1 |
by Rudolf10000 Mon, 2019-04-29 19:34 |
|
|
Need Help Setting Up Dual VESC on Trampa by MIKEtheBIKE » Wed, 2020-09-09 03:15 |
0 |
by MIKEtheBIKE Wed, 2020-09-09 03:15 |
|
|
New version. by ThierryGTLTS » Thu, 2017-09-07 19:22 |
6 |
by Hectortcher Wed, 2020-03-04 11:21 |
|
|
Newbie question : How to switch to RPM mode ? by Lezard » Thu, 2024-02-29 19:30 |
1 |
by Lezard Mon, 2024-03-11 15:18 |
|
|
No brakes in PID Speed Control mode by karololo » Tue, 2019-10-15 11:31 |
3 |
by Gesndrery Thu, 2019-12-26 07:00 |
|
|
no effect on set erpm/speed limit by xenon321 » Sat, 2021-04-24 20:43 |
0 |
by xenon321 Sun, 2021-04-25 16:53 |
|
|
Noobs need to update and / or configure old VESC 4.12 by Loops » Tue, 2023-02-07 11:49 |
0 |
by Loops Tue, 2023-02-07 11:49 |
|
|
Not responding to the throttle when moving backwards by jprojpro » Fri, 2022-07-15 15:30 |
3 |
by mannerz91 Mon, 2024-08-05 22:23 |
|
|
Not sure if parameter update in VESC tool works by srinath » Thu, 2023-06-08 11:29 |
0 |
by srinath Thu, 2023-06-08 11:29 |
|
|
Not sure what motor weight to choose in VESC Tool Setup Wizard by edvin » Mon, 2024-06-24 13:28 |
0 |
by edvin Mon, 2024-06-24 13:28 |
|
|
NRF connection error by Denn » Wed, 2022-02-02 11:17 |
0 |
by Denn Wed, 2022-02-02 11:17 |
|
|
Nrf connection error by vufmihai » Sat, 2020-04-25 22:00 |
0 |
by vufmihai Sat, 2020-04-25 22:00 |
|
|
NRF5X SWD Prog detection broken, always detects NRF52832 512K/64K by zippy » Sun, 2021-06-06 16:19 |
1 |
by zippy Sun, 2021-06-06 17:58 |
|
|
Old versions of VESC Tool by TheFallen » Thu, 2018-07-05 19:47 |
30 |
by FEA555 Sun, 2024-05-19 19:16 |
|
|
Older version of VESC Tool by Gas_Sn4ke » Fri, 2018-11-30 09:28 |
0 |
by Gas_Sn4ke Fri, 2018-11-30 09:28 |
|
|
One ESC two Motors by Vdca » Sat, 2023-09-23 20:24 |
0 |
by Vdca Sat, 2023-09-23 20:24 |
|
|
one motor spinning faster than the other? by jon218white » Mon, 2020-12-14 22:57 |
0 |
by jon218white Mon, 2020-12-14 22:57 |
|
|
One trasmitter two receivers by vikiki » Wed, 2021-11-17 20:40 |
4 |
by Johnvoss Fri, 2021-12-24 03:57 |
|
|
Overheating protection, voltage-/current-limitation etc. by kianK » Thu, 2021-04-15 07:23 |
2 |
by lilliamhoyle Wed, 2021-07-07 09:36 |
|
|
Parameters for efoil by vladek » Thu, 2023-04-20 12:54 |
0 |
by vladek Thu, 2023-04-20 12:54 |
|
|
Parametre for Low RPM Limit by ilan248@gmail.com » Wed, 2019-07-10 11:01 |
1 |
by askker Thu, 2019-07-11 05:04 |
|
|
Partial throttle input smoothing / jerky control by moose09876 » Thu, 2023-08-10 20:56 |
1 |
by moose09876 Sun, 2023-09-24 19:28 |
|
|
Pc requirement to run vesc software by proget.snc » Mon, 2021-04-12 10:57 |
1 |
by benjamin Wed, 2021-04-14 19:47 |
Log in to post new content in the forum.
