You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Question about FOC Wizard by proget.snc » Thu, 2021-08-26 16:31 |
2 |
by proget.snc Thu, 2021-09-02 14:23 |
|
|
Motor whine with HFI? by christopher.h.poole » Mon, 2021-04-19 15:49 |
2 |
by christopher.h.poole Tue, 2021-06-15 21:18 |
|
|
[Solved] VESC Tool "could not deserialize motor configuration" with custom firmware by bsobeloffgittes » Fri, 2024-05-03 20:30 |
2 |
by rafeh1 Wed, 2024-11-06 09:14 |
|
|
VESC runs only with 50% duty cycle by Nimrod0201 » Wed, 2024-07-10 18:30 |
2 |
by Nimrod0201 Sat, 2024-07-13 11:34 |
|
|
brake switch/brake regen question by smallbikefun » Sat, 2024-04-06 01:48 |
2 |
by smallbikefun Sun, 2024-04-14 22:08 |
|
|
BUG - RAMPING on VESC TOOL? by Filcas » Tue, 2019-12-10 19:29 |
2 |
by Filcas Wed, 2019-12-11 17:15 |
|
|
Vesc tool 1.26.. issue with firmware updates? by beetbocks » Tue, 2019-12-17 10:17 |
2 |
by Stupidspencer Wed, 2019-12-25 23:04 |
|
|
motor detection - what to expect when spinning up the motor by grantmoy74 » Sat, 2019-12-28 11:58 |
2 |
by grantmoy74 Sun, 2019-12-29 05:21 |
|
|
How to update VESC Tool? by Heimfried » Wed, 2020-02-05 10:35 |
2 |
by marialoise Fri, 2020-03-13 20:20 |
|
|
I Mac Vesc tool !!!! by PHATTY » Fri, 2019-10-11 17:56 |
2 |
by Bender Wed, 2021-03-10 14:39 |
|
|
Battery Voltage Settings by huffauden19 » Wed, 2020-03-04 23:17 |
2 |
by laser30 Sat, 2021-03-13 16:57 |
|
|
Cannot connect to vesc tool app by sharpshooterjd » Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
|
|
Motor Stuck at 55% Duty Cycle by motion_sickness » Sun, 2021-11-14 16:47 |
1 |
by drdrs Sun, 2021-11-14 21:20 |
|
|
Lisp scripting questions/suggestions/remarks by Gatze » Sun, 2022-04-24 12:13 |
1 |
by Jamesavery22 Sat, 2025-01-04 04:58 |
|
|
Use sensors on the output shaft of a motor attached to a large gear ratio gearbox by davidq1688 » Wed, 2022-04-27 05:23 |
1 |
by tobiokanobi Thu, 2022-04-28 14:48 |
|
|
Vesc doesn't react to can messages from PC by BorisDeroo » Fri, 2021-12-17 16:54 |
1 |
by yuri12 Wed, 2022-02-09 17:33 |
|
|
inconsistent behavior after motor control using FOC by alexantosh » Wed, 2022-01-05 10:24 |
1 |
by frank Wed, 2022-01-05 11:21 |
|
|
Pictures from "Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller"? by timmertens » Thu, 2022-06-16 17:56 |
1 |
by frank Thu, 2022-06-16 19:47 |
|
|
Taking 5-6 seconds for running motor under ADC mode by asnamp » Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
|
|
download logfiles (Express) via mobile? by Dan Dyse » Fri, 2025-05-23 08:33 |
1 |
by Dan Dyse Wed, 2025-08-20 14:34 |
|
|
PPM throttle detected in Vesc Tool but has no effect on motor by maxim1977 » Sat, 2025-07-26 06:03 |
1 |
by ftpkmarcelo Sun, 2025-08-10 06:07 |
|
|
FOC detection needs load? by tuloski » Thu, 2018-09-13 10:19 |
1 |
by TechAUmNu Thu, 2018-09-13 12:26 |
|
|
Unable to Make Changes in VESC Tool – field weakening Options Missing by asaf1462 » Tue, 2024-12-17 16:27 |
1 |
by Jamesavery22 Sat, 2025-01-04 19:32 |
|
|
build VESC Tool on Linux Mint by cb » Fri, 2018-04-13 16:19 |
1 |
by benjamin Mon, 2018-04-16 10:59 |
|
|
Motor Poles by Enak » Fri, 2017-09-08 00:57 |
1 |
by ThierryGTLTS Fri, 2017-09-08 09:01 |
Log in to post new content in the forum.
