You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Feature request: Raw hall data. by Roger Wolff » Mon, 2018-06-11 15:49 |
4 |
by blubbi321 Tue, 2022-03-29 16:32 |
|
|
Change HW after wrong Firmware Update by Hassi » Sun, 2017-10-01 15:46 |
4 |
by benjamin Sun, 2017-10-22 23:32 |
|
|
VESC Tool 3.0 can't run input wizzard by thib » Mon, 2021-09-27 00:58 |
4 |
by frank Fri, 2021-10-29 10:07 |
|
|
Delay on reverse function on electric boat by FreddyForLaunch » Tue, 2021-06-01 12:31 |
4 |
by electricfox Wed, 2022-08-17 20:59 |
|
|
ADC throttle is accelerating th full throttle quickly by Buddah » Sun, 2019-09-15 23:32 |
4 |
by jimtzer Wed, 2021-06-30 17:54 |
|
|
Smart Reverse Minimum Erpm by ZenRides » Wed, 2022-02-16 05:36 |
4 |
by nabil sassi Tue, 2022-04-12 23:21 |
|
|
Can't spin both motors over CAN-bus by Kokonenen » Wed, 2023-04-19 11:19 |
4 |
by mansi712 Wed, 2024-10-30 13:40 |
|
|
One trasmitter two receivers by vikiki » Wed, 2021-11-17 20:40 |
4 |
by Johnvoss Fri, 2021-12-24 03:57 |
|
|
Regen Braking not working by James Hamilton » Thu, 2022-05-26 16:08 |
4 |
by frank Wed, 2022-06-01 18:14 |
|
|
Bafang hub motor setup by Kent Tabor » Fri, 2020-10-16 03:48 |
4 |
by Racing2Learn Sun, 2024-05-05 18:31 |
|
|
Docker images for vesc build? by dammfine » Thu, 2020-04-23 18:56 |
4 |
by brycej Fri, 2020-07-24 18:06 |
|
|
Cannot get any PPM signals from Arduino. Or is it just the VESC tool? by MaxMaker1 » Thu, 2018-06-21 23:06 |
4 |
by tuloski Thu, 2018-09-13 09:36 |
|
|
Maximum Duty Cycle limit is 95% by shimdidly » Sun, 2017-10-01 19:59 |
4 |
by shimdidly Sat, 2017-10-07 01:42 |
|
|
Data logging by charper » Wed, 2019-05-22 00:48 |
4 |
by StvMan Sun, 2021-03-21 17:20 |
|
|
Been at it for like 14 hours... HALP by mnchvgs79 » Wed, 2021-03-03 22:03 |
4 |
by TheFallen Sun, 2021-03-07 15:25 |
|
|
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies » Wed, 2021-04-28 23:59 |
4 |
by mansi712 Tue, 2024-11-05 17:57 |
|
|
Connect VESC4.7 over USB by Lars_Dierickx » Thu, 2023-03-09 16:13 |
4 |
by Lawrence Sun, 2025-04-27 16:23 |
|
|
How to get Max Torque at start by player107 » Fri, 2023-04-07 09:55 |
4 |
by Trooth Fri, 2024-02-23 06:52 |
|
|
Motor not Spinning Up During Setup Wizard by superjay » Tue, 2021-11-23 07:03 |
4 |
by superjay Wed, 2021-11-24 11:25 |
|
|
VESC Tool 2.06 not working either on windows. by oger » Fri, 2020-05-08 00:11 |
4 |
by kjskjs00 Fri, 2023-11-24 23:18 |
|
|
Please explain the parameters in VESC-Tool by Knight » Wed, 2018-09-05 11:45 |
3 |
by Pimousse Tue, 2018-10-30 19:21 |
|
|
Help needed for VESC set up! by mbagrey » Wed, 2018-09-19 22:07 |
3 |
by Roger Wolff Sun, 2018-09-30 16:15 |
|
|
How Can I make the tool work with FW 3.5 instead of just 3.58? by ipbyrne » Fri, 2019-07-26 18:20 |
3 |
by frank Wed, 2019-08-14 14:01 |
|
|
Setup parameters for battery in VESC Tool by Ulrich » Tue, 2019-02-26 11:47 |
3 |
by Photolad61 Wed, 2019-03-27 17:26 |
|
|
FFT in VESC Tool by RSR » Thu, 2018-05-31 14:37 |
3 |
by TechAUmNu Thu, 2018-05-31 16:28 |
Log in to post new content in the forum.
