You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
How to log events on a non bluetooth onewheel setup by carasta » Sat, 2023-05-13 22:01 |
0 |
by carasta Sat, 2023-05-13 22:01 |
|
|
HFI plot by Rick van der Sloot » Sun, 2022-10-02 22:26 |
0 |
by Rick van der Sloot Sun, 2022-10-02 22:26 |
|
|
Issue with Vesc Tool: MPU6050 IMU Not Detected After Power Cycling by Lennart Duijn » Thu, 2023-06-01 21:54 |
0 |
by Lennart Duijn Fri, 2023-06-02 09:03 |
|
|
Latched power switch on Trampa VESC 6 75A by dversity » Wed, 2023-06-28 00:36 |
0 |
by dversity Wed, 2023-06-28 00:36 |
|
|
Unable to connect to vesc through can bus by Kupofty » Thu, 2022-10-20 16:24 |
0 |
by Kupofty Thu, 2022-10-20 16:24 |
|
|
Power Monitor and Logging by IntDesign » Thu, 2023-07-06 18:08 |
0 |
by IntDesign Thu, 2023-07-06 18:08 |
|
|
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto » Sun, 2022-11-27 16:34 |
0 |
by Miniproto Sun, 2022-11-27 16:34 |
|
|
Vesc120 ADC1 FAIL by sbman » Thu, 2026-07-09 01:41 |
0 |
by sbman Thu, 2026-07-09 01:41 |
|
|
D vs omega control by rsarver » Wed, 2021-03-17 14:44 |
0 |
by rsarver Wed, 2021-03-17 14:44 |
|
|
VESC failure presumably due to current oscillations at high current by rsarver » Wed, 2021-03-24 22:06 |
0 |
by rsarver Wed, 2021-03-24 22:06 |
|
|
ADC Positive and Negative Ramping Time - not working by Astropower » Tue, 2019-05-28 22:41 |
0 |
by Astropower Tue, 2019-05-28 22:41 |
|
|
VESC Tool for Android & GPS/GNSS sharing? by ahagge » Fri, 2021-10-01 05:04 |
0 |
by ahagge Fri, 2021-10-01 05:04 |
|
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann » Wed, 2021-04-21 13:48 |
0 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
|
|
no effect on set erpm/speed limit by xenon321 » Sat, 2021-04-24 20:43 |
0 |
by xenon321 Sun, 2021-04-25 16:53 |
|
|
setting up development environment for android by jaghori.sasan » Wed, 2019-02-20 14:59 |
0 |
by jaghori.sasan Wed, 2019-02-20 14:59 |
|
|
read RPM over CAN by nblange » Mon, 2021-05-03 20:43 |
0 |
by nblange Mon, 2021-05-03 20:43 |
|
|
one motor spinning faster than the other? by jon218white » Mon, 2020-12-14 22:57 |
0 |
by jon218white Mon, 2020-12-14 22:57 |
|
|
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed » Fri, 2019-08-02 20:00 |
0 |
by Munkyheed Fri, 2019-08-02 20:00 |
|
|
Update FW on multiple VESC pcbs using CAN issue by Offline » Thu, 2021-05-20 07:36 |
0 |
by Offline Thu, 2021-05-20 07:36 |
|
|
Wrong Motor detection values after STM swap dual vesc 6 by Micro » Sun, 2019-08-18 01:59 |
0 |
by Micro Sun, 2019-08-18 02:14 |
|
|
Update FW using vesc tool over phone by SkaterBoy58 » Thu, 2019-03-14 05:33 |
0 |
by SkaterBoy58 Thu, 2019-03-14 05:33 |
|
|
Incorrect parameter detection by macieksz@pro.onet.pl » Fri, 2019-08-30 16:05 |
0 |
by macieksz@pro.onet.pl Fri, 2019-08-30 16:05 |
|
|
Logging real time data from a custom app by SirPolPol » Sat, 2021-02-06 22:24 |
0 |
by SirPolPol Sat, 2021-02-06 22:24 |
|
|
Vesc tool mobile for raspbian by Idoff » Sat, 2019-03-30 19:24 |
0 |
by Idoff Sat, 2019-03-30 19:24 |
|
|
Benchmark regenerative braking by diggis » Fri, 2021-02-19 10:01 |
0 |
by diggis Fri, 2021-02-19 10:01 |
Log in to post new content in the forum.
