You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
New version. by ThierryGTLTS » Thu, 2017-09-07 19:22 |
6 |
by Hectortcher Wed, 2020-03-04 11:21 |
|
|
Keyboard control not working (Remote works) by bukl » Sun, 2020-05-24 16:51 |
6 |
by sanketh1691 Wed, 2021-10-06 20:45 |
|
|
Driving Alternator wired as BLDC motor with VESC6 by LittleTinker » Thu, 2019-10-10 13:06 |
6 |
by flyingbrike Wed, 2021-09-22 20:16 |
|
|
Trouble downloading the tool by maxhertz » Tue, 2022-01-25 03:12 |
6 |
by frank Sat, 2022-02-05 11:02 |
|
|
Version 3.01 destroyed version 2.06 too by Knaubel » Sun, 2022-05-15 21:23 |
6 |
by Knaubel Wed, 2022-05-18 16:16 |
|
|
Bad detection problem by baron456 » Fri, 2018-06-29 17:56 |
5 |
by frank Fri, 2018-07-13 14:41 |
|
|
HW4.12 with FW 3.27, FOC OK, BLDC problems. by ThierryGTLTS » Thu, 2017-09-07 11:14 |
5 |
by ThierryGTLTS Sat, 2017-09-16 18:45 |
|
|
Bluetooth RX/TX by eastcoastkiter » Fri, 2019-06-28 19:02 |
5 |
by radler Sat, 2020-06-20 17:06 |
|
|
Custom plots in VESC - Tool by kinzma » Sun, 2019-07-28 11:44 |
5 |
by jfaille Wed, 2021-02-10 07:50 |
|
|
Current In vs Current Motor by hacksmithCabe » Thu, 2021-09-30 21:59 |
5 |
by y-hasebe Mon, 2021-12-13 15:17 |
|
|
Version 2.03 won't open by marialoise » Fri, 2020-03-13 20:24 |
5 |
by pwilkinson91 Tue, 2023-06-27 22:07 |
|
|
How to Enable kill switch support in Firmware 5.03 by iserai2r » Sat, 2022-02-05 13:59 |
5 |
by rodrigo.baronio Tue, 2023-02-14 02:27 |
|
|
experiment tab rpm ramp up and dual separate motor control by tobiokanobi » Thu, 2022-04-14 20:20 |
5 |
by tobiokanobi Tue, 2022-04-26 15:32 |
|
|
Motor control by ptss37 » Wed, 2021-12-08 06:52 |
5 |
by ptss37 Fri, 2021-12-10 03:24 |
|
|
Adding HM-10 Compatibility with Small Changes to Code by Jfriesen » Sat, 2018-06-09 00:45 |
5 |
by CTSchorsch Mon, 2020-01-06 07:11 |
|
|
RPM Limit not working by chinzw » Wed, 2017-09-06 09:29 |
5 |
by ThierryGTLTS Thu, 2017-09-07 11:05 |
|
|
Maximum possible Baudrate in UART? by nlabs » Sun, 2018-04-08 01:52 |
5 |
by anttok Tue, 2020-12-01 00:26 |
|
|
Questions on VESC tool by da_rul0r » Wed, 2019-08-14 09:47 |
5 |
by Isi Mon, 2021-04-12 17:34 |
|
|
Dual Motor Setup Wizard Not working 1.08 by captclearleft » Tue, 2019-04-16 01:05 |
5 |
by buggermenot Sat, 2022-05-28 15:11 |
|
|
Data logging for dual VESC on Android VESC-tool by elmardus » Wed, 2021-10-20 16:13 |
5 |
by SamuL Fri, 2023-02-17 00:55 |
|
|
Feature request: Raw hall data. by Roger Wolff » Mon, 2018-06-11 15:49 |
4 |
by blubbi321 Tue, 2022-03-29 16:32 |
|
|
Change HW after wrong Firmware Update by Hassi » Sun, 2017-10-01 15:46 |
4 |
by benjamin Sun, 2017-10-22 23:32 |
|
|
How to increase startup torque? by Enak » Fri, 2017-09-08 01:14 |
4 |
by vadicus Tue, 2021-02-23 19:44 |
|
|
Docker images for vesc build? by dammfine » Thu, 2020-04-23 18:56 |
4 |
by brycej Fri, 2020-07-24 18:06 |
|
|
How to get Max Torque at start by player107 » Fri, 2023-04-07 09:55 |
4 |
by Trooth Fri, 2024-02-23 06:52 |
Log in to post new content in the forum.
