You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
The engine stopped spinning after updating firmware by brian adilman » Wed, 2022-01-26 17:40 |
0 |
by brian adilman Wed, 2022-01-26 19:15 |
|
|
NRF connection error by Denn » Wed, 2022-02-02 11:17 |
0 |
by Denn Wed, 2022-02-02 11:17 |
|
|
Throttle Input reading not changing by niko_la » Fri, 2022-07-22 02:40 |
0 |
by niko_la Fri, 2022-07-22 02:40 |
|
|
Vesc_tool OVER_TEMP_FET by XIII » Thu, 2018-01-11 17:26 |
0 |
by XIII Thu, 2018-01-11 17:26 |
|
|
Different rpm when using 3 vesc with can-bus by ewakegermanyhq » Wed, 2022-08-03 17:03 |
0 |
by ewakegermanyhq Wed, 2022-08-03 17:03 |
|
|
Upgrade the Bootloader? by erikfed » Tue, 2022-03-08 20:32 |
0 |
by erikfed Tue, 2022-03-08 20:32 |
|
|
getting started by SilkyD » Mon, 2021-10-25 12:49 |
0 |
by SilkyD Mon, 2021-10-25 12:49 |
|
|
VESC Tool Device UI not shown on Raspberry Pi/Linux by Sebastiaan Koning » Mon, 2024-12-02 13:19 |
0 |
by Sebastiaan Koning Mon, 2024-12-02 13:19 |
|
|
Vesc tool app not installed on Samsung a02s by Zuky » Sun, 2025-08-03 20:31 |
0 |
by Zuky Sun, 2025-08-03 20:32 |
|
|
Flipsky FSESC 6.7PRO and bluetooth module by phonkie » Mon, 2025-08-18 06:33 |
0 |
by phonkie Mon, 2025-08-18 06:33 |
|
|
lispBM command "gpio-hold" by Jamesavery22 » Sat, 2025-01-04 20:46 |
0 |
by Jamesavery22 Sat, 2025-01-04 20:46 |
|
|
Battery profiles? by ahagge » Mon, 2025-09-01 16:36 |
0 |
by ahagge Mon, 2025-09-01 16:36 |
|
|
Odys Alpha X3 Pro Settings by flashice » Mon, 2025-01-06 14:28 |
0 |
by flashice Mon, 2025-01-06 14:34 |
|
|
turn counter by player107 » Wed, 2025-09-10 22:52 |
0 |
by player107 Wed, 2025-09-10 22:52 |
|
|
Urgent Help Connecting TS5700N8501-like Magnetic Encoder by jumana » Tue, 2025-01-14 19:37 |
0 |
by jumana Tue, 2025-01-14 19:37 |
|
|
limited mode by Satrio » Fri, 2025-09-26 16:31 |
0 |
by Satrio Fri, 2025-09-26 16:31 |
|
|
Vesc Tool 6.06 test version 2 error by NOAI » Sat, 2025-01-25 13:00 |
0 |
by NOAI Sat, 2025-01-25 13:00 |
|
|
PID Speed Control Type by User18 » Fri, 2025-10-31 19:35 |
0 |
by User18 Fri, 2025-10-31 19:35 |
|
|
Very low Flux Linkage calulation FOC,General Tab - 0.0xx mWb by kjjajsdASHD » Sun, 2025-02-02 13:59 |
0 |
by kjjajsdASHD Sun, 2025-02-02 13:59 |
|
|
VESC Tool IMU Problem by 13.meshhi » Sun, 2025-11-16 23:40 |
0 |
by 13.meshhi Sun, 2025-11-16 23:40 |
|
|
How I disconnect CAN communation between two ESCs in dual channel ESC by Adesh Kute » Tue, 2025-12-16 08:10 |
0 |
by Adesh Kute Tue, 2025-12-16 08:10 |
|
|
IOS Vesc Tool uses wrong keypad for data entry by Fluffhead616 » Mon, 2025-12-22 23:36 |
0 |
by Fluffhead616 Mon, 2025-12-22 23:36 |
|
|
Difficult motor FOC detection by Roger Wolff » Wed, 2025-02-12 19:42 |
0 |
by Roger Wolff Wed, 2025-02-12 19:42 |
|
|
No Single Direction ADC in FW v6.06??? by rcalicea » Fri, 2026-02-13 09:15 |
0 |
by rcalicea Fri, 2026-02-13 09:23 |
|
|
Error creating appimage by EduardoHP28 » Fri, 2025-02-21 07:35 |
0 |
by EduardoHP28 Fri, 2025-02-21 07:37 |
Log in to post new content in the forum.
