You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Need Help Setting Up Dual VESC on Trampa by MIKEtheBIKE » Wed, 2020-09-09 03:15 |
0 |
by MIKEtheBIKE Wed, 2020-09-09 03:15 |
|
|
Vesc mAh reading by th0masrtg » Tue, 2020-09-29 08:48 |
0 |
by th0masrtg Wed, 2020-09-30 19:58 |
|
|
Detection for a drone outrunner 515 kV and 775 kV by MaksK » Thu, 2020-06-04 16:05 |
0 |
by MaksK Thu, 2020-06-04 16:05 |
|
|
Terminal Command for Current? by Mannerow » Thu, 2020-10-29 23:07 |
0 |
by Mannerow Thu, 2020-10-29 23:07 |
|
|
ESC State, Switch Value, and Motor Position unknown by 175_pilot » Wed, 2020-11-04 04:22 |
0 |
by 175_pilot Wed, 2020-11-04 04:22 |
|
|
FOC Motor Detection Values Incorrect, PID Tuning Advice? by bmwman91 » Mon, 2020-07-06 03:09 |
0 |
by bmwman91 Mon, 2020-07-06 03:21 |
|
|
Vesc 6, FW 5.1, WH charged is not being logged by BalorNG » Thu, 2020-12-03 14:19 |
0 |
by BalorNG Thu, 2020-12-03 14:19 |
|
|
Data Loggin Values by BLeaCH » Sat, 2020-04-04 07:37 |
0 |
by BLeaCH Sat, 2020-04-04 07:37 |
|
|
Running a DC 12V trolling motor with a 4.20. Hidden current limit?. by Impuls60 » Wed, 2020-07-22 14:32 |
0 |
by Impuls60 Wed, 2020-07-22 19:00 |
|
|
Help i can not setup my motors by jakson01 » Fri, 2022-09-09 18:37 |
0 |
by jakson01 Fri, 2022-09-09 18:37 |
|
|
How to log events on a non bluetooth onewheel setup by carasta » Sat, 2023-05-13 22:01 |
0 |
by carasta Sat, 2023-05-13 22:01 |
|
|
HFI plot by Rick van der Sloot » Sun, 2022-10-02 22:26 |
0 |
by Rick van der Sloot Sun, 2022-10-02 22:26 |
|
|
Issue with Vesc Tool: MPU6050 IMU Not Detected After Power Cycling by Lennart Duijn » Thu, 2023-06-01 21:54 |
0 |
by Lennart Duijn Fri, 2023-06-02 09:03 |
|
|
Latched power switch on Trampa VESC 6 75A by dversity » Wed, 2023-06-28 00:36 |
0 |
by dversity Wed, 2023-06-28 00:36 |
|
|
Unable to connect to vesc through can bus by Kupofty » Thu, 2022-10-20 16:24 |
0 |
by Kupofty Thu, 2022-10-20 16:24 |
|
|
Power Monitor and Logging by IntDesign » Thu, 2023-07-06 18:08 |
0 |
by IntDesign Thu, 2023-07-06 18:08 |
|
|
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto » Sun, 2022-11-27 16:34 |
0 |
by Miniproto Sun, 2022-11-27 16:34 |
|
|
Previous versions of VESC Tool by Drosselmeier » Fri, 2023-07-14 12:49 |
0 |
by Drosselmeier Fri, 2023-07-14 12:49 |
|
|
Download for Windows VESC-Tool from FW5.02 era? by bmwman91 » Mon, 2023-07-24 02:03 |
0 |
by bmwman91 Mon, 2023-07-24 02:37 |
|
|
Motor not running after applying SINE/COSINE settings by DHOUT » Fri, 2023-01-27 03:32 |
0 |
by DHOUT Fri, 2023-01-27 03:32 |
|
|
duty cicle 95% but current not at max by rodrigo.baronio » Mon, 2023-02-06 15:52 |
0 |
by rodrigo.baronio Mon, 2023-02-06 15:52 |
|
|
One ESC two Motors by Vdca » Sat, 2023-09-23 20:24 |
0 |
by Vdca Sat, 2023-09-23 20:24 |
|
|
Noobs need to update and / or configure old VESC 4.12 by Loops » Tue, 2023-02-07 11:49 |
0 |
by Loops Tue, 2023-02-07 11:49 |
|
|
i try, i try but... by rastafouille » Tue, 2023-10-10 16:19 |
0 |
by rastafouille Tue, 2023-10-10 16:21 |
|
|
Configuration Issue with Dual FlipSky 75100 Controllers by daktylus » Thu, 2023-10-12 03:17 |
0 |
by daktylus Thu, 2023-10-12 03:17 |
Log in to post new content in the forum.
