You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Vesc_tool OVER_TEMP_FET by XIII » Thu, 2018-01-11 17:26 |
0 |
by XIII Thu, 2018-01-11 17:26 |
|
|
UART Safety Feature by jaghori.sasan » Wed, 2019-09-04 18:45 |
0 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
|
|
arrow key hot working (neither on the app) but the board works correclty by lorenzidomenico94 » Tue, 2020-01-14 11:30 |
0 |
by lorenzidomenico94 Tue, 2020-01-14 11:30 |
|
|
VESC tool load empty by arminoonk » Thu, 2020-01-16 14:51 |
0 |
by arminoonk Thu, 2020-01-16 14:51 |
|
|
FOC Encoder autotune issue by David_Lo » Tue, 2020-01-21 11:54 |
0 |
by David_Lo Tue, 2020-01-21 11:54 |
|
|
Input Setup Wizard - Update Firmware by pmg » Thu, 2020-02-13 09:54 |
0 |
by pmg Thu, 2020-02-13 09:54 |
|
|
ADC and arrow input dont work by stefann » Wed, 2019-10-09 18:51 |
0 |
by stefann Wed, 2019-10-09 20:04 |
|
|
Reconstruct detection control algorithm inside the tool by kaanozgen » Wed, 2020-02-26 18:50 |
0 |
by kaanozgen Wed, 2020-02-26 18:50 |
|
|
Changing minimum duty cycle prevents VESC from connecting via USB while ADC throttle is connected by shimdidly » Sun, 2017-10-15 00:48 |
0 |
by shimdidly Sun, 2017-10-15 00:48 |
|
|
Acceleration Temperature Decrease (Relevant Safety Update) by frank » Sun, 2017-10-29 22:19 |
0 |
by frank Sun, 2017-10-29 22:19 |
|
|
Vesc120 ADC1 FAIL by sbman » Thu, 2026-07-09 01:41 |
0 |
by sbman Thu, 2026-07-09 01:41 |
|
|
How to enable can bus communication by Kayleb » Sun, 2026-08-16 20:29 |
0 |
by Kayleb Mon, 2026-08-17 11:52 |
|
|
Different rpm when using 3 vesc with can-bus by ewakegermanyhq » Wed, 2022-08-03 17:03 |
0 |
by ewakegermanyhq Wed, 2022-08-03 17:03 |
|
|
Upgrade the Bootloader? by erikfed » Tue, 2022-03-08 20:32 |
0 |
by erikfed Tue, 2022-03-08 20:32 |
|
|
getting started by SilkyD » Mon, 2021-10-25 12:49 |
0 |
by SilkyD Mon, 2021-10-25 12:49 |
|
|
Error on log-file recording: Could not get Positioning Working by hpb66 » Mon, 2022-05-23 08:23 |
0 |
by hpb66 Mon, 2022-05-23 08:23 |
|
|
questions about "RUN DETECTION" by yuri12 » Thu, 2022-01-20 04:30 |
0 |
by yuri12 Thu, 2022-01-20 04:30 |
|
|
The engine stopped spinning after updating firmware by brian adilman » Wed, 2022-01-26 17:40 |
0 |
by brian adilman Wed, 2022-01-26 19:15 |
|
|
NRF connection error by Denn » Wed, 2022-02-02 11:17 |
0 |
by Denn Wed, 2022-02-02 11:17 |
|
|
Throttle Input reading not changing by niko_la » Fri, 2022-07-22 02:40 |
0 |
by niko_la Fri, 2022-07-22 02:40 |
|
|
FOC Motor Detection Values Incorrect, PID Tuning Advice? by bmwman91 » Mon, 2020-07-06 03:09 |
0 |
by bmwman91 Mon, 2020-07-06 03:21 |
|
|
Vesc 6, FW 5.1, WH charged is not being logged by BalorNG » Thu, 2020-12-03 14:19 |
0 |
by BalorNG Thu, 2020-12-03 14:19 |
|
|
Communication over UART or CAN by JCLNEIL » Wed, 2023-12-13 14:36 |
0 |
by JCLNEIL Wed, 2023-12-13 14:36 |
|
|
How VESCTOOL Determines the foc_sensor_mode by NATUITION » Tue, 2024-05-28 11:29 |
0 |
by NATUITION Tue, 2024-05-28 11:29 |
|
|
Electronic Differential Control System by matias123 » Mon, 2023-12-18 03:44 |
0 |
by matias123 Mon, 2023-12-18 03:44 |
Log in to post new content in the forum.
