You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Can't spin both motors over CAN-bus by Kokonenen » Wed, 2023-04-19 11:19 |
4 |
by mansi712 Wed, 2024-10-30 13:40 |
|
|
Data logging by charper » Wed, 2019-05-22 00:48 |
4 |
by StvMan Sun, 2021-03-21 17:20 |
|
|
Delay on reverse function on electric boat by FreddyForLaunch » Tue, 2021-06-01 12:31 |
4 |
by electricfox Wed, 2022-08-17 20:59 |
|
|
VESC Tool 3.0 can't run input wizzard by thib » Mon, 2021-09-27 00:58 |
4 |
by frank Fri, 2021-10-29 10:07 |
|
|
VESC Tool disappeared from App Store by volkswagenbug » Thu, 2024-06-13 21:40 |
4 |
by Sybernetix Sat, 2024-06-15 11:32 |
|
|
Flipsky can't connect to vesc tool by vescbeginer » Fri, 2024-08-02 20:16 |
4 |
by Bbonsack Tue, 2026-05-26 02:05 |
|
|
Regen Braking not working by James Hamilton » Thu, 2022-05-26 16:08 |
4 |
by frank Wed, 2022-06-01 18:14 |
|
|
Cannot get any PPM signals from Arduino. Or is it just the VESC tool? by MaxMaker1 » Thu, 2018-06-21 23:06 |
4 |
by tuloski Thu, 2018-09-13 09:36 |
|
|
Maximum Duty Cycle limit is 95% by shimdidly » Sun, 2017-10-01 19:59 |
4 |
by shimdidly Sat, 2017-10-07 01:42 |
|
|
Smart Reverse Minimum Erpm by ZenRides » Wed, 2022-02-16 05:36 |
4 |
by nabil sassi Tue, 2022-04-12 23:21 |
|
|
One trasmitter two receivers by vikiki » Wed, 2021-11-17 20:40 |
4 |
by Johnvoss Fri, 2021-12-24 03:57 |
|
|
Docker images for vesc build? by dammfine » Thu, 2020-04-23 18:56 |
4 |
by brycej Fri, 2020-07-24 18:06 |
|
|
Bafang hub motor setup by Kent Tabor » Fri, 2020-10-16 03:48 |
4 |
by Racing2Learn Sun, 2024-05-05 18:31 |
|
|
Questions on VESC tool by da_rul0r » Wed, 2019-08-14 09:47 |
5 |
by Isi Mon, 2021-04-12 17:34 |
|
|
Dual Motor Setup Wizard Not working 1.08 by captclearleft » Tue, 2019-04-16 01:05 |
5 |
by buggermenot Sat, 2022-05-28 15:11 |
|
|
Current In vs Current Motor by hacksmithCabe » Thu, 2021-09-30 21:59 |
5 |
by y-hasebe Mon, 2021-12-13 15:17 |
|
|
Motor control by ptss37 » Wed, 2021-12-08 06:52 |
5 |
by ptss37 Fri, 2021-12-10 03:24 |
|
|
Bad detection problem by baron456 » Fri, 2018-06-29 17:56 |
5 |
by frank Fri, 2018-07-13 14:41 |
|
|
How to Enable kill switch support in Firmware 5.03 by iserai2r » Sat, 2022-02-05 13:59 |
5 |
by rodrigo.baronio Tue, 2023-02-14 02:27 |
|
|
HW4.12 with FW 3.27, FOC OK, BLDC problems. by ThierryGTLTS » Thu, 2017-09-07 11:14 |
5 |
by ThierryGTLTS Sat, 2017-09-16 18:45 |
|
|
experiment tab rpm ramp up and dual separate motor control by tobiokanobi » Thu, 2022-04-14 20:20 |
5 |
by tobiokanobi Tue, 2022-04-26 15:32 |
|
|
"CAN bus support is not enabled in this build of VESC Tool" by hdfghdfgh » Wed, 2023-04-26 16:13 |
5 |
by Nshoup Sat, 2026-01-10 01:30 |
|
|
Custom plots in VESC - Tool by kinzma » Sun, 2019-07-28 11:44 |
5 |
by jfaille Wed, 2021-02-10 07:50 |
|
|
Bluetooth RX/TX by eastcoastkiter » Fri, 2019-06-28 19:02 |
5 |
by radler Sat, 2020-06-20 17:06 |
|
|
Version 2.03 won't open by marialoise » Fri, 2020-03-13 20:24 |
5 |
by pwilkinson91 Tue, 2023-06-27 22:07 |
Log in to post new content in the forum.
