You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
How Can I make the tool work with FW 3.5 instead of just 3.58? by ipbyrne » Fri, 2019-07-26 18:20 |
3 |
by frank Wed, 2019-08-14 14:01 |
|
|
Setup parameters for battery in VESC Tool by Ulrich » Tue, 2019-02-26 11:47 |
3 |
by Photolad61 Wed, 2019-03-27 17:26 |
|
|
Dual VESC and One Motor Stops Spinning by f0n » Tue, 2025-02-11 02:22 |
3 |
by DavidjohnNeff Wed, 2025-02-12 05:57 |
|
|
VESC Tool RPM not the actual in real life by Poh Boon pin » Sun, 2021-07-11 16:00 |
3 |
by Klamauk Wed, 2026-01-14 22:32 |
|
|
windows 7 VESC TOOL 1.25 wont open/not responding HELP PLEASE by timgoebel12@gma... » Tue, 2019-11-12 00:42 |
3 |
by yehsk8rz Sat, 2021-12-04 20:52 |
|
|
supported firmware by velolac » Mon, 2020-01-13 22:55 |
3 |
by velolac Tue, 2020-01-14 21:47 |
|
|
Question about COMM_GET_IMU_DATA packet by rrzaripov » Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
|
|
No brakes in PID Speed Control mode by karololo » Tue, 2019-10-15 11:31 |
3 |
by Gesndrery Thu, 2019-12-26 07:00 |
|
|
If firmware aint broke, dont fix it. by nickw1881 » Thu, 2019-10-31 07:32 |
3 |
by frank Wed, 2019-11-06 12:39 |
|
|
Smart Reverse Minimum Erpm by ZenRides » Wed, 2022-02-16 05:36 |
4 |
by nabil sassi Tue, 2022-04-12 23:21 |
|
|
Cannot get any PPM signals from Arduino. Or is it just the VESC tool? by MaxMaker1 » Thu, 2018-06-21 23:06 |
4 |
by tuloski Thu, 2018-09-13 09:36 |
|
|
Maximum Duty Cycle limit is 95% by shimdidly » Sun, 2017-10-01 19:59 |
4 |
by shimdidly Sat, 2017-10-07 01:42 |
|
|
One trasmitter two receivers by vikiki » Wed, 2021-11-17 20:40 |
4 |
by Johnvoss Fri, 2021-12-24 03:57 |
|
|
Regen Braking not working by James Hamilton » Thu, 2022-05-26 16:08 |
4 |
by frank Wed, 2022-06-01 18:14 |
|
|
Connect vesc tool with ANT BMS by Vdca » Sun, 2024-01-14 23:15 |
4 |
by Timo Wedel Sat, 2024-07-27 14:41 |
|
|
Docker images for vesc build? by dammfine » Thu, 2020-04-23 18:56 |
4 |
by brycej Fri, 2020-07-24 18:06 |
|
|
Bafang hub motor setup by Kent Tabor » Fri, 2020-10-16 03:48 |
4 |
by Racing2Learn Sun, 2024-05-05 18:31 |
|
|
Connect VESC4.7 over USB by Lars_Dierickx » Thu, 2023-03-09 16:13 |
4 |
by Lawrence Sun, 2025-04-27 16:23 |
|
|
How to get Max Torque at start by player107 » Fri, 2023-04-07 09:55 |
4 |
by Trooth Fri, 2024-02-23 06:52 |
|
|
Vesc Tool 6.02 compiling Error on Ubuntu (res_fw.qrc) by Gos1 » Wed, 2023-06-21 17:23 |
4 |
by rafeh1 Sun, 2024-10-27 07:54 |
|
|
Data logging by charper » Wed, 2019-05-22 00:48 |
4 |
by StvMan Sun, 2021-03-21 17:20 |
|
|
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies » Wed, 2021-04-28 23:59 |
4 |
by mansi712 Tue, 2024-11-05 17:57 |
|
|
Been at it for like 14 hours... HALP by mnchvgs79 » Wed, 2021-03-03 22:03 |
4 |
by thefallen Sun, 2021-03-07 15:25 |
|
|
Feature request: Raw hall data. by Roger Wolff » Mon, 2018-06-11 15:49 |
4 |
by blubbi321 Tue, 2022-03-29 16:32 |
|
|
Change HW after wrong Firmware Update by Hassi » Sun, 2017-10-01 15:46 |
4 |
by benjamin Sun, 2017-10-22 23:32 |
Log in to post new content in the forum.
