You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Vesc mAh reading by th0masrtg » Tue, 2020-09-29 08:48 |
0 |
by th0masrtg Wed, 2020-09-30 19:58 |
|
|
Motor not running after applying SINE/COSINE settings by DHOUT » Fri, 2023-01-27 03:32 |
0 |
by DHOUT Fri, 2023-01-27 03:32 |
|
|
Is anyone else having the same problems by Jheckman » Mon, 2022-08-22 16:33 |
0 |
by Jheckman Mon, 2022-08-22 16:33 |
|
|
FSESC seems to be speed limiting my motor by 5amsung4 » Sat, 2022-09-03 18:50 |
0 |
by 5amsung4 Mon, 2022-09-05 07:51 |
|
|
Help i can not setup my motors by jakson01 » Fri, 2022-09-09 18:37 |
0 |
by jakson01 Fri, 2022-09-09 18:37 |
|
|
HFI plot by Rick van der Sloot » Sun, 2022-10-02 22:26 |
0 |
by Rick van der Sloot Sun, 2022-10-02 22:26 |
|
|
Unable to connect to vesc through can bus by Kupofty » Thu, 2022-10-20 16:24 |
0 |
by Kupofty Thu, 2022-10-20 16:24 |
|
|
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto » Sun, 2022-11-27 16:34 |
0 |
by Miniproto Sun, 2022-11-27 16:34 |
|
|
IMU not working after power cycle by Lennart Duijn » Mon, 2023-01-09 22:08 |
0 |
by Lennart Duijn Mon, 2023-01-09 22:08 |
|
|
setting up development environment for android by jaghori.sasan » Wed, 2019-02-20 14:59 |
0 |
by jaghori.sasan Wed, 2019-02-20 14:59 |
|
|
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed » Fri, 2019-08-02 20:00 |
0 |
by Munkyheed Fri, 2019-08-02 20:00 |
|
|
Wrong Motor detection values after STM swap dual vesc 6 by Micro » Sun, 2019-08-18 01:59 |
0 |
by Micro Sun, 2019-08-18 02:14 |
|
|
Update FW using vesc tool over phone by SkaterBoy58 » Thu, 2019-03-14 05:33 |
0 |
by SkaterBoy58 Thu, 2019-03-14 05:33 |
|
|
Incorrect parameter detection by macieksz@pro.onet.pl » Fri, 2019-08-30 16:05 |
0 |
by macieksz@pro.onet.pl Fri, 2019-08-30 16:05 |
|
|
Vesc tool mobile for raspbian by Idoff » Sat, 2019-03-30 19:24 |
0 |
by Idoff Sat, 2019-03-30 19:24 |
|
|
How to activate e-brake on e-scooter with the throttle by Donatas Sukelis » Sat, 2019-04-27 10:09 |
0 |
by Donatas Sukelis Sat, 2019-04-27 10:09 |
|
|
Connecting ABI encoder to VESC by Gas_Sn4ke » Mon, 2018-11-26 06:00 |
0 |
by Gas_Sn4ke Mon, 2018-11-26 06:00 |
|
|
Problem with encoder readings with arduino by ruthvikchanda » Thu, 2018-12-06 07:06 |
0 |
by ruthvikchanda Thu, 2018-12-06 07:06 |
|
|
ADC Positive and Negative Ramping Time - not working by Astropower » Tue, 2019-05-28 22:41 |
0 |
by Astropower Tue, 2019-05-28 22:41 |
|
|
VESC failure presumably due to current oscillations at high current by rsarver » Wed, 2021-03-24 22:06 |
0 |
by rsarver Wed, 2021-03-24 22:06 |
|
|
VESC Tool for Android & GPS/GNSS sharing? by ahagge » Fri, 2021-10-01 05:04 |
0 |
by ahagge Fri, 2021-10-01 05:04 |
|
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann » Wed, 2021-04-21 13:48 |
0 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
|
|
no effect on set erpm/speed limit by xenon321 » Sat, 2021-04-24 20:43 |
0 |
by xenon321 Sun, 2021-04-25 16:53 |
|
|
read RPM over CAN by nblange » Mon, 2021-05-03 20:43 |
0 |
by nblange Mon, 2021-05-03 20:43 |
|
|
one motor spinning faster than the other? by jon218white » Mon, 2020-12-14 22:57 |
0 |
by jon218white Mon, 2020-12-14 22:57 |
Log in to post new content in the forum.
