You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Setup parameters for battery in VESC Tool by Ulrich » Tue, 2019-02-26 11:47 |
3 |
by Photolad61 Wed, 2019-03-27 17:26 |
|
|
How to control motor using VESC tool in computer at constant rpm? by vimi94 » Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
|
|
VESC Tool RPM not the actual in real life by Poh Boon pin » Sun, 2021-07-11 16:00 |
3 |
by Klamauk Wed, 2026-01-14 22:32 |
|
|
Windows 10 free tool wont open... by zip » Sun, 2024-06-30 07:09 |
3 |
by Mastersam Wed, 2024-10-16 11:56 |
|
|
Flipsky can't connect to vesc tool by vescbeginer » Fri, 2024-08-02 20:16 |
3 |
by wimleo Wed, 2025-03-19 17:49 |
|
|
If firmware aint broke, dont fix it. by nickw1881 » Thu, 2019-10-31 07:32 |
3 |
by frank Wed, 2019-11-06 12:39 |
|
|
windows 7 VESC TOOL 1.25 wont open/not responding HELP PLEASE by timgoebel12@gma... » Tue, 2019-11-12 00:42 |
3 |
by yehsk8rz Sat, 2021-12-04 20:52 |
|
|
supported firmware by velolac » Mon, 2020-01-13 22:55 |
3 |
by velolac Tue, 2020-01-14 21:47 |
|
|
Question about COMM_GET_IMU_DATA packet by rrzaripov » Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
|
|
No brakes in PID Speed Control mode by karololo » Tue, 2019-10-15 11:31 |
3 |
by Gesndrery Thu, 2019-12-26 07:00 |
|
|
Not responding to the throttle when moving backwards by jprojpro » Fri, 2022-07-15 15:30 |
3 |
by mannerz91 Mon, 2024-08-05 22:23 |
|
|
motor experiment does nothing by greaterebiz » Mon, 2022-04-11 18:27 |
3 |
by swinckler Fri, 2022-07-01 14:38 |
|
|
Vesc can't connect to vesc tool by Roansky1 » Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
|
|
Motor temperature, how to set limit >120 C ? by RSR » Wed, 2018-08-22 12:40 |
3 |
by Danny Bokma Thu, 2018-08-23 07:19 |
|
|
Please explain the parameters in VESC-Tool by Knight » Wed, 2018-09-05 11:45 |
3 |
by Pimousse Tue, 2018-10-30 19:21 |
|
|
Help needed for VESC set up! by mbagrey » Wed, 2018-09-19 22:07 |
3 |
by Roger Wolff Sun, 2018-09-30 16:15 |
|
|
FFT in VESC Tool by RSR » Thu, 2018-05-31 14:37 |
3 |
by TechAUmNu Thu, 2018-05-31 16:28 |
|
|
Position issue by Davideo » Tue, 2017-09-19 16:48 |
3 |
by bOneWheel Mon, 2023-10-30 15:07 |
|
|
Dual VESC and One Motor Stops Spinning by f0n » Tue, 2025-02-11 02:22 |
3 |
by DavidjohnNeff Wed, 2025-02-12 05:57 |
|
|
Hoverboard Motor Setup by CadillacF1 » Sat, 2020-07-11 05:26 |
3 |
by meziked Wed, 2025-07-02 16:13 |
|
|
Can the PPM mapping be changed so that higher duty cycle means slower speed? by UncleJoe » Mon, 2020-05-25 11:46 |
3 |
by UncleJoe Thu, 2020-11-19 15:06 |
|
|
How to keep motor at 0RPM by zapshe » Thu, 2022-09-08 13:51 |
3 |
by DaganWal Wed, 2023-07-19 04:38 |
|
|
ios bluetooth connection Flipsky 75100 pro by Frederik Aksel Holst » Sun, 2023-07-09 16:31 |
3 |
by sandrino Mon, 2023-07-24 16:43 |
|
|
Data logging by charper » Wed, 2019-05-22 00:48 |
4 |
by StvMan Sun, 2021-03-21 17:20 |
|
|
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies » Wed, 2021-04-28 23:59 |
4 |
by mansi712 Tue, 2024-11-05 17:57 |
Log in to post new content in the forum.
