You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
"bad detection result received" impossible to achieved motor detection ! by titimomotete » Wed, 2019-03-20 17:21 |
2 |
by doom Mon, 2019-08-05 10:52 |
|
|
Windows 10 free tool wont open... by zip » Sun, 2024-06-30 07:09 |
3 |
by Mastersam Wed, 2024-10-16 11:56 |
|
|
Flipsky can't connect to vesc tool by vescbeginer » Fri, 2024-08-02 20:16 |
3 |
by wimleo Wed, 2025-03-19 17:49 |
|
|
supported firmware by velolac » Mon, 2020-01-13 22:55 |
3 |
by velolac Tue, 2020-01-14 21:47 |
|
|
Question about COMM_GET_IMU_DATA packet by rrzaripov » Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
|
|
No brakes in PID Speed Control mode by karololo » Tue, 2019-10-15 11:31 |
3 |
by Gesndrery Thu, 2019-12-26 07:00 |
|
|
If firmware aint broke, dont fix it. by nickw1881 » Thu, 2019-10-31 07:32 |
3 |
by frank Wed, 2019-11-06 12:39 |
|
|
windows 7 VESC TOOL 1.25 wont open/not responding HELP PLEASE by timgoebel12@gma... » Tue, 2019-11-12 00:42 |
3 |
by yehsk8rz Sat, 2021-12-04 20:52 |
|
|
motor experiment does nothing by greaterebiz » Mon, 2022-04-11 18:27 |
3 |
by swinckler Fri, 2022-07-01 14:38 |
|
|
4k monitor problem by nlabs » Wed, 2017-11-01 07:36 |
3 |
by benjamin Fri, 2017-11-03 09:22 |
|
|
VESC Tool 0.87 by pieschie » Sun, 2018-08-26 12:38 |
3 |
by Roger Wolff Sun, 2018-09-16 12:00 |
|
|
Serial port error when Encoder detection is complete by VirtB » Wed, 2018-08-29 03:03 |
3 |
by VirtB Sun, 2018-09-02 03:33 |
|
|
Vesc can't connect to vesc tool by Roansky1 » Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
|
|
Vesc-Tool Raspbian compatible build by mjc60 » Fri, 2017-09-08 18:20 |
3 |
by RSR Tue, 2017-09-19 11:35 |
|
|
Not responding to the throttle when moving backwards by jprojpro » Fri, 2022-07-15 15:30 |
3 |
by mannerz91 Mon, 2024-08-05 22:23 |
|
|
FOC detection.... by Roger Wolff » Thu, 2018-05-24 17:37 |
3 |
by TechAUmNu Sun, 2018-05-27 21:14 |
|
|
Version 0.84, some problems with ADC, see 2nd post please! by ThierryGTLTS » Sun, 2017-10-29 14:11 |
3 |
by ThierryGTLTS Fri, 2017-11-03 16:56 |
|
|
Dual VESC and One Motor Stops Spinning by f0n » Tue, 2025-02-11 02:22 |
3 |
by DavidjohnNeff Wed, 2025-02-12 05:57 |
|
|
Can the PPM mapping be changed so that higher duty cycle means slower speed? by UncleJoe » Mon, 2020-05-25 11:46 |
3 |
by UncleJoe Thu, 2020-11-19 15:06 |
|
|
Hoverboard Motor Setup by CadillacF1 » Sat, 2020-07-11 05:26 |
3 |
by meziked Wed, 2025-07-02 16:13 |
|
|
How to keep motor at 0RPM by zapshe » Thu, 2022-09-08 13:51 |
3 |
by DaganWal Wed, 2023-07-19 04:38 |
|
|
ios bluetooth connection Flipsky 75100 pro by Frederik Aksel Holst » Sun, 2023-07-09 16:31 |
3 |
by sandrino Mon, 2023-07-24 16:43 |
|
|
fsesc 4.20 CAN bus not detecting by LeonD » Sat, 2021-05-08 15:44 |
3 |
by MartyMcFlyFord Sat, 2022-06-04 16:54 |
|
|
Help "ERASE" Lisp Script that crashes VESC TOOL (terminal command?) by ebikebuilder_yt » Thu, 2024-08-01 20:16 |
3 |
by jonasb Mon, 2025-09-22 21:00 |
|
|
speed value with geared hub motor by swampland » Tue, 2024-08-27 16:27 |
3 |
by swampland Thu, 2024-08-29 17:31 |
Log in to post new content in the forum.
