You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Not responding to the throttle when moving backwards by jprojpro » Fri, 2022-07-15 15:30 |
3 |
by mannerz91 Mon, 2024-08-05 22:23 |
|
|
motor experiment does nothing by greaterebiz » Mon, 2022-04-11 18:27 |
3 |
by swinckler Fri, 2022-07-01 14:38 |
|
|
Vesc can't connect to vesc tool by Roansky1 » Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
|
|
Motor temperature, how to set limit >120 C ? by RSR » Wed, 2018-08-22 12:40 |
3 |
by Danny Bokma Thu, 2018-08-23 07:19 |
|
|
Please explain the parameters in VESC-Tool by Knight » Wed, 2018-09-05 11:45 |
3 |
by Pimousse Tue, 2018-10-30 19:21 |
|
|
Help needed for VESC set up! by mbagrey » Wed, 2018-09-19 22:07 |
3 |
by Roger Wolff Sun, 2018-09-30 16:15 |
|
|
FFT in VESC Tool by RSR » Thu, 2018-05-31 14:37 |
3 |
by TechAUmNu Thu, 2018-05-31 16:28 |
|
|
Position issue by Davideo » Tue, 2017-09-19 16:48 |
3 |
by bOneWheel Mon, 2023-10-30 15:07 |
|
|
Can the PPM mapping be changed so that higher duty cycle means slower speed? by UncleJoe » Mon, 2020-05-25 11:46 |
3 |
by UncleJoe Thu, 2020-11-19 15:06 |
|
|
Hoverboard Motor Setup by CadillacF1 » Sat, 2020-07-11 05:26 |
3 |
by meziked Wed, 2025-07-02 16:13 |
|
|
How to keep motor at 0RPM by zapshe » Thu, 2022-09-08 13:51 |
3 |
by DaganWal Wed, 2023-07-19 04:38 |
|
|
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies » Wed, 2021-04-28 23:59 |
4 |
by mansi712 Tue, 2024-11-05 17:57 |
|
|
Been at it for like 14 hours... HALP by mnchvgs79 » Wed, 2021-03-03 22:03 |
4 |
by TheFallen Sun, 2021-03-07 15:25 |
|
|
Motor not Spinning Up During Setup Wizard by superjay » Tue, 2021-11-23 07:03 |
4 |
by superjay Wed, 2021-11-24 11:25 |
|
|
Cannot get any PPM signals from Arduino. Or is it just the VESC tool? by MaxMaker1 » Thu, 2018-06-21 23:06 |
4 |
by tuloski Thu, 2018-09-13 09:36 |
|
|
Maximum Duty Cycle limit is 95% by shimdidly » Sun, 2017-10-01 19:59 |
4 |
by shimdidly Sat, 2017-10-07 01:42 |
|
|
VESC Tool 2.06 not working either on windows. by oger » Fri, 2020-05-08 00:11 |
4 |
by kjskjs00 Fri, 2023-11-24 23:18 |
|
|
Can't spin both motors over CAN-bus by Kokonenen » Wed, 2023-04-19 11:19 |
4 |
by mansi712 Wed, 2024-10-30 13:40 |
|
|
How do I compile the VESC Tool? by ipbyrne » Wed, 2019-07-24 16:58 |
4 |
by a.dahhak Fri, 2021-01-01 15:25 |
|
|
VESC Tool 3.0 can't run input wizzard by thib » Mon, 2021-09-27 00:58 |
4 |
by frank Fri, 2021-10-29 10:07 |
|
|
Delay on reverse function on electric boat by FreddyForLaunch » Tue, 2021-06-01 12:31 |
4 |
by electricfox Wed, 2022-08-17 20:59 |
|
|
ADC throttle is accelerating th full throttle quickly by Buddah » Sun, 2019-09-15 23:32 |
4 |
by jimtzer Wed, 2021-06-30 17:54 |
|
|
Smart Reverse Minimum Erpm by ZenRides » Wed, 2022-02-16 05:36 |
4 |
by nabil sassi Tue, 2022-04-12 23:21 |
|
|
One trasmitter two receivers by vikiki » Wed, 2021-11-17 20:40 |
4 |
by Johnvoss Fri, 2021-12-24 03:57 |
|
|
Regen Braking not working by James Hamilton » Thu, 2022-05-26 16:08 |
4 |
by frank Wed, 2022-06-01 18:14 |
Log in to post new content in the forum.
