You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
48v problems by vufmihai » Wed, 2020-07-22 22:53 |
2 |
by vufmihai Fri, 2020-07-31 07:25 |
|
|
Setup for very slow < 100RPM on Maytech 6365 Motor. by jason3w » Tue, 2020-09-01 10:52 |
2 |
by asapereira Mon, 2020-09-14 10:26 |
|
|
VESC Tool Platinum : Windows 7 - Not working by moorem » Mon, 2020-05-18 23:19 |
2 |
by TheFallen Tue, 2020-12-15 12:06 |
|
|
Firmware issues by salvasalce » Tue, 2022-12-13 16:12 |
2 |
by Lennart Duijn Mon, 2023-01-09 22:10 |
|
|
Installing VESC Tool on Jetson Nano by mrburns19 » Tue, 2023-02-07 04:54 |
2 |
by mrburns19 Sun, 2023-02-12 01:44 |
|
|
Vesctool otg by meashman » Sat, 2022-08-06 10:05 |
2 |
by meashman Wed, 2022-08-17 06:39 |
|
|
VESC tool and sk8-esc V6 set up shows incorrectcurrent usage by DominykasS » Fri, 2022-09-30 13:54 |
2 |
by Frizzaper Wed, 2023-11-15 04:25 |
|
|
current control via CAN not working by STTS » Thu, 2021-08-12 11:51 |
2 |
by mm_iem Mon, 2021-08-30 18:00 |
|
|
VESC tool for windows by djevIen » Mon, 2019-06-17 08:02 |
2 |
by frank Fri, 2022-06-03 21:33 |
|
|
Question about FOC Wizard by proget.snc » Thu, 2021-08-26 16:31 |
2 |
by proget.snc Thu, 2021-09-02 14:23 |
|
|
Motor whine with HFI? by christopher.h.poole » Mon, 2021-04-19 15:49 |
2 |
by christopher.h.poole Tue, 2021-06-15 21:18 |
|
|
[SOLVED] RPM setting not working by olivierskypullc... » Wed, 2019-02-27 12:14 |
2 |
by olivierskypullc... Wed, 2019-03-06 10:10 |
|
|
Vesc Tool not opening on windows computer by maccert » Sat, 2019-03-02 11:04 |
2 |
by Luca Torani Sun, 2019-03-03 20:32 |
|
|
Connect VESC to Keyboard/Wireless Joystick by sanketh1691 » Mon, 2021-10-04 20:58 |
2 |
by sanketh1691 Wed, 2021-10-06 18:58 |
|
|
VESC TOOL cant connect to hardware by svs » Sat, 2021-04-24 22:06 |
2 |
by jose carceller Sun, 2022-08-21 00:43 |
|
|
Is it possible to stop a motor at one exact desired location without hall sensor? by vimi94 » Thu, 2019-08-15 10:58 |
2 |
by vimi94 Tue, 2019-08-20 13:37 |
|
|
BEMF plot not working with VESC6 by ESCam » Tue, 2019-03-12 21:29 |
2 |
by ESCam Tue, 2019-03-19 18:03 |
|
|
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies » Wed, 2021-04-28 23:59 |
2 |
by Gloobox Wed, 2022-11-30 18:39 |
|
|
motor to slow and no power by Thiery Vardon » Sat, 2021-01-09 10:45 |
2 |
by Thiery Vardon Tue, 2021-01-12 13:27 |
|
|
How to Traction Control VESC 6 by Karl » Thu, 2018-10-11 03:33 |
2 |
by marti Wed, 2018-10-17 06:02 |
|
|
Voltage measurement calibration? by pyryjansson » Tue, 2019-04-30 20:19 |
2 |
by frank Wed, 2022-11-30 09:55 |
|
|
VESCTOOL - Multiple VESC simultaneous configuration (Same CANBUS ID issues) by Filcas » Thu, 2021-02-18 20:52 |
2 |
by Filcas Fri, 2021-02-19 01:37 |
|
|
load cell data logging by magnus.w » Thu, 2019-05-02 00:21 |
2 |
by Tom Burton Wed, 2019-11-06 16:43 |
|
|
Use Vesc-Tool to run two motors simultaneously via CAN by microlomaniac » Thu, 2021-06-17 11:55 |
2 |
by spacewalker Tue, 2021-06-22 08:23 |
|
|
Wrong HW version selected during FW update by babyboi » Sat, 2018-12-15 21:30 |
2 |
by babyboi Sat, 2018-12-22 03:55 |
Log in to post new content in the forum.
