You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Braking noisy on Hoverboards hubs . by lurch » Mon, 2021-11-08 15:59 |
2 |
by lurch Mon, 2021-11-15 21:35 |
|
|
BRAND NEW R SPEC DUAL 6355 (4.12 VESC) SET UP ISSUES by rodriguezjoe1@b... » Mon, 2020-09-07 17:50 |
0 |
by rodriguezjoe1@b... Mon, 2020-09-07 17:50 |
|
|
Bricked my VESC six what now? by atat » Sun, 2018-05-20 13:07 |
0 |
by atat Sun, 2018-05-20 14:28 |
|
|
Brushless or brushed motor for autonomous rc-car by Joe_Lowtech » Thu, 2018-12-20 11:56 |
4 |
by Joe_Lowtech Tue, 2019-03-05 11:00 |
|
|
BT module and UART remote simultaneously on dual vescs by Rc 44 » Fri, 2023-12-01 18:40 |
1 |
by Rc 44 Mon, 2024-01-08 04:48 |
|
|
Building the vesc firmware in Chibi Studio by chris1seto » Sat, 2019-01-12 02:36 |
1 |
by kinzma Thu, 2019-02-14 09:42 |
|
|
Burned my VESC 6 MKV. Wrong polarity by okhsunrog » Thu, 2022-04-07 01:44 |
4 |
by frank Thu, 2022-04-07 10:27 |
|
|
C80100 Outrunner 50kv does not want to spin. by Wormsnake » Sun, 2019-03-03 10:30 |
1 |
by TheFallen Sun, 2019-03-10 17:54 |
|
|
Calculator by kstuck » Tue, 2019-12-10 18:30 |
0 |
by kstuck Tue, 2019-12-10 18:30 |
|
|
CAN Analyzer by min » Tue, 2022-05-03 10:38 |
0 |
by min Tue, 2022-05-03 10:38 |
|
|
Can bus and Arduino by Snabelost » Wed, 2023-06-14 10:30 |
2 |
by Snabelost Thu, 2023-06-15 08:37 |
|
|
Can bus and BLDC vs FOC by Torbjorn » Fri, 2022-11-11 11:08 |
4 |
by Torbjorn Tue, 2022-11-15 14:37 |
|
|
Can bus communication. by Piamen » Wed, 2019-11-27 06:47 |
0 |
by Piamen Wed, 2019-11-27 06:47 |
|
|
CAN Bus Control by External Host by josh » Fri, 2018-11-30 06:43 |
3 |
by Jack_Li Mon, 2019-07-01 10:37 |
|
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
|
Can control Vesc 100/250 by David_1 » Sat, 2022-06-18 01:31 |
1 |
by David_1 Sun, 2022-06-19 19:44 |
|
|
CAN eRPM report by alxsfrm » Mon, 2022-02-07 11:01 |
0 |
by alxsfrm Mon, 2022-02-07 11:01 |
|
|
Can I change control mode on the fly through the UART port? by spork » Wed, 2019-03-13 02:24 |
2 |
by spork Wed, 2019-03-13 15:41 |
|
|
Can i change the controller (LQFP64) with (LQFP100) with same Firmware? by GalihRiddle » Thu, 2019-09-05 13:44 |
2 |
by GalihRiddle Mon, 2019-09-09 13:22 |
|
|
can I fit a VESC in my e-skate? by 6diegodiego9 » Thu, 2021-01-21 20:42 |
1 |
by skyline1970 Tue, 2021-02-02 21:30 |
|
|
Can I measure a 1.5 KW AC Servo with VESC Tool by Don_Karlos » Sun, 2024-05-26 21:28 |
2 |
by adilrepas Mon, 2024-08-05 18:54 |
|
|
Can I use 12V power supply? by ryde6 » Sun, 2021-04-25 08:19 |
2 |
by vadicus Wed, 2021-07-14 21:01 |
|
|
Can larger BLDC motors be controlled with VESC? by Heimfried » Sun, 2020-02-02 21:29 |
3 |
by Heimfried Thu, 2020-02-06 22:39 |
|
|
Can motor parameters be detected with shaft load? by powerlabor001 » Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
|
|
Can not adjust the RPM on my 1350 w motor by Arne Norway » Wed, 2019-01-09 18:47 |
6 |
by sam.vanratt Sun, 2019-01-13 13:36 |
Log in to post new content in the forum.
