You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
2 Speed ADC control by totalgeek9224 » Mon, 2025-09-22 19:47 |
0 |
by totalgeek9224 Mon, 2025-09-22 19:47 |
|
|
VESC specialist required. by BlackPanthera » Mon, 2022-07-18 17:11 |
0 |
by BlackPanthera Mon, 2022-07-18 17:11 |
|
|
Problem with encoder readings with arduino by ruthvikchanda » Thu, 2018-12-06 07:06 |
0 |
by ruthvikchanda Thu, 2018-12-06 10:23 |
|
|
Voltage Calibration by Frantin » Mon, 2026-04-20 21:40 |
0 |
by Frantin Mon, 2026-04-20 21:40 |
|
|
How do you turn on traction control ( I can't remember) by msim2 » Fri, 2022-05-20 22:06 |
0 |
by msim2 Fri, 2022-05-20 22:06 |
|
|
Duty Cycle with brake switch and PAS by m620 » Tue, 2026-04-28 03:50 |
0 |
by m620 Tue, 2026-04-28 03:50 |
|
|
Problem with Android app by Er-Chispa » Wed, 2025-10-08 20:58 |
0 |
by Er-Chispa Wed, 2025-10-08 21:02 |
|
|
vesc canbus control PPM by JiaheXu » Thu, 2023-04-13 20:17 |
0 |
by JiaheXu Thu, 2023-04-13 20:17 |
|
|
Vesc gps control by Erik » Thu, 2019-11-14 20:38 |
0 |
by Erik Thu, 2019-11-14 20:38 |
|
|
Settings by aquamarin » Sat, 2023-07-01 16:11 |
0 |
by aquamarin Sat, 2023-07-01 16:11 |
|
|
How does controlling two different motors over CAN bus really work? by oangelo » Sat, 2023-04-15 20:05 |
0 |
by oangelo Sat, 2023-04-15 20:05 |
|
|
Spikes in RPM causing the ride to be bumpy by dsuresh » Tue, 2021-03-23 21:55 |
0 |
by dsuresh Tue, 2021-03-23 21:55 |
|
|
VESC6 with DRV8320 by cromoly » Wed, 2023-04-19 02:40 |
0 |
by cromoly Wed, 2023-04-19 02:40 |
|
|
Problem in BLDC PWM pulse by Jose Jacob » Wed, 2021-03-24 17:18 |
0 |
by Jose Jacob Wed, 2021-03-24 17:18 |
|
|
Using Multiple VESCs in Robotics? by Kristof123 » Sat, 2023-07-15 19:00 |
0 |
by Kristof123 Sat, 2023-07-15 19:00 |
|
|
Configuration via CAN? by mrPalomar » Tue, 2023-05-16 02:22 |
0 |
by mrPalomar Tue, 2023-05-16 02:22 |
|
|
Problems driving motors in RPM mode by jediengineer » Fri, 2023-03-10 14:03 |
0 |
by jediengineer Fri, 2023-03-10 19:51 |
|
|
Integration of VESC with a display using I2C by dsuresh » Thu, 2021-05-20 19:32 |
0 |
by dsuresh Thu, 2021-05-20 19:32 |
|
|
Basic VESC troubleshooting (postmortem?) by N_COUNTER » Tue, 2023-03-14 10:58 |
0 |
by N_COUNTER Tue, 2023-03-14 11:01 |
|
|
IPM parameter adjust by rbargallo » Sun, 2021-05-23 22:43 |
0 |
by rbargallo Sun, 2021-05-23 22:43 |
|
|
Drive frequency and command rate question by jediengineer » Sun, 2023-03-19 19:07 |
0 |
by jediengineer Sun, 2023-03-19 19:08 |
|
|
Calculator by kstuck » Tue, 2019-12-10 18:30 |
0 |
by kstuck Tue, 2019-12-10 18:30 |
|
|
Issues running a gimbal motor by ksau » Thu, 2021-03-11 16:44 |
0 |
by ksau Thu, 2021-03-11 16:44 |
|
|
3Shul 700A reporting negative current spikes by reobaird » Sat, 2023-03-25 03:22 |
0 |
by reobaird Mon, 2023-03-27 09:34 |
|
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 » Wed, 2019-10-23 23:12 |
0 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
Log in to post new content in the forum.
