You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Problem with Android app by Er-Chispa » Wed, 2025-10-08 20:58 |
0 |
by Er-Chispa Wed, 2025-10-08 21:02 |
|
|
About How to control the "FLIPSKY Dual FSESC6.7 PLUS" by tonyH » Tue, 2025-10-14 11:35 |
0 |
by tonyH Tue, 2025-10-14 11:35 |
|
|
Voltage spikes on BEMF scope by Sgw32 » Wed, 2020-11-18 16:03 |
0 |
by Sgw32 Wed, 2020-11-18 16:06 |
|
|
Vesc help by Roy Voroncovs » Sat, 2026-05-30 11:34 |
0 |
by Roy Voroncovs Sat, 2026-05-30 11:34 |
|
|
VESC with asynchronous motors by afbbfa » Fri, 2022-07-29 22:51 |
0 |
by afbbfa Fri, 2022-07-29 22:51 |
|
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse » Fri, 2022-06-03 08:13 |
0 |
by notahorse Fri, 2022-06-03 08:13 |
|
|
FOC ABS_OVER_CURRENT at high RPM by Philippe Larouche » Sat, 2026-06-06 18:24 |
0 |
by Philippe Larouche Sat, 2026-06-06 18:24 |
|
|
Hall sensor port repeatedly fried on original hardware by Rc 44 » Fri, 2025-10-24 22:44 |
0 |
by Rc 44 Fri, 2025-10-24 22:44 |
|
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 » Mon, 2022-08-01 18:08 |
0 |
by moose09876 Mon, 2022-08-01 18:08 |
|
|
VESC as generator - settings confirmation by justinlsquire » Mon, 2022-06-06 02:44 |
0 |
by justinlsquire Mon, 2022-06-06 02:44 |
|
|
tutorial for hfi by TONY61 » Mon, 2026-06-15 17:11 |
0 |
by TONY61 Mon, 2026-06-15 17:11 |
|
|
VESC to spin motor after power up? by A_Baum92881 » Fri, 2025-10-31 06:01 |
0 |
by A_Baum92881 Fri, 2025-10-31 17:21 |
|
|
Does PLL measure the REAL motor speed by wyk » Mon, 2020-11-23 08:34 |
0 |
by wyk Mon, 2020-11-23 08:34 |
|
|
Vesc Orientation Python by flomai28 » Mon, 2025-11-10 09:44 |
0 |
by flomai28 Mon, 2025-11-10 09:44 |
|
|
Could use some help tuning for low speed by Berrie » Tue, 2025-07-15 20:24 |
0 |
by Berrie Tue, 2025-07-15 20:24 |
|
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset » Thu, 2022-08-04 01:44 |
0 |
by liminalsunset Thu, 2022-08-04 01:44 |
|
|
Because..why not: Full Self Riding Skateboard (autonomous skateboard) by x78163 » Wed, 2022-06-08 17:33 |
0 |
by x78163 Wed, 2022-06-08 17:33 |
|
|
Kaabo mantis 10 elite(minimotors) FLIPSJY 75100 DUAL ALU PCB by Musik117 » Fri, 2025-07-18 14:33 |
0 |
by Musik117 Fri, 2025-07-18 14:33 |
|
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings » Fri, 2022-08-05 11:06 |
0 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
|
|
Configuration via CAN? by mrPalomar » Tue, 2023-05-16 02:22 |
0 |
by mrPalomar Tue, 2023-05-16 02:22 |
|
|
Problems driving motors in RPM mode by jediengineer » Fri, 2023-03-10 14:03 |
0 |
by jediengineer Fri, 2023-03-10 19:51 |
|
|
Integration of VESC with a display using I2C by dsuresh » Thu, 2021-05-20 19:32 |
0 |
by dsuresh Thu, 2021-05-20 19:32 |
|
|
Basic VESC troubleshooting (postmortem?) by N_COUNTER » Tue, 2023-03-14 10:58 |
0 |
by N_COUNTER Tue, 2023-03-14 11:01 |
|
|
IPM parameter adjust by rbargallo » Sun, 2021-05-23 22:43 |
0 |
by rbargallo Sun, 2021-05-23 22:43 |
|
|
Drive frequency and command rate question by jediengineer » Sun, 2023-03-19 19:07 |
0 |
by jediengineer Sun, 2023-03-19 19:08 |
Log in to post new content in the forum.
