You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
base on VESC6_MkVI by gavin » Wed, 2025-06-04 15:48 |
0 |
by gavin Wed, 2025-06-04 15:48 |
|
|
4 fried vesc's Australia by adamclarke1985 » Tue, 2020-03-31 20:48 |
0 |
by adamclarke1985 Tue, 2020-03-31 21:24 |
|
|
Servo Mode / ODrive on VESC by JulianT » Tue, 2020-02-04 09:19 |
0 |
by JulianT Tue, 2020-02-04 09:19 |
|
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 » Fri, 2020-04-10 12:33 |
0 |
by olaf2273 Mon, 2020-04-27 15:34 |
|
|
Firmware V4.00 field oriented control motor jerk but wont spin by jordanlow » Thu, 2020-02-13 14:41 |
0 |
by jordanlow Thu, 2020-02-13 14:41 |
|
|
Hi by elsie » Thu, 2018-01-25 02:49 |
0 |
by elsie Thu, 2018-01-25 16:23 |
|
|
Maximum Motor RPM will not reached by Skyver » Sun, 2022-01-23 10:53 |
0 |
by Skyver Sun, 2022-01-23 10:53 |
|
|
Running PID position Control with FOC sensorless by talabo » Fri, 2021-12-03 17:21 |
0 |
by talabo Fri, 2021-12-03 17:21 |
|
|
Interessante Arbeiten zum Thema eSkateboard by barney » Tue, 2017-01-03 18:55 |
0 |
by barney Tue, 2017-01-03 18:55 |
|
|
Connecting AMT203 to Flipsky 4.20 ESC by kgeo0003 » Mon, 2022-01-24 06:44 |
0 |
by kgeo0003 Mon, 2022-01-24 09:00 |
|
|
Autonomous RC car with Focbox suddenly stops by Autocar » Mon, 2021-12-06 06:55 |
0 |
by Autocar Mon, 2021-12-06 06:55 |
|
|
Incorrect Batt Current Readings in FOC but not in BLDC by vadicus » Tue, 2020-02-25 20:06 |
0 |
by vadicus Tue, 2020-02-25 20:09 |
|
|
custom firmware by vufmihai » Thu, 2020-01-16 09:06 |
0 |
by vufmihai Thu, 2020-01-16 09:06 |
|
|
Comms plug and leads by craig w » Fri, 2021-12-24 00:25 |
0 |
by craig w Fri, 2021-12-24 00:25 |
|
|
Dollar signs break private messages by TechAUmNu » Tue, 2018-04-24 18:09 |
0 |
by TechAUmNu Tue, 2018-04-24 18:09 |
|
|
PAS only one signal + BLE by sifourquier » Fri, 2021-12-31 19:08 |
0 |
by sifourquier Fri, 2021-12-31 19:08 |
|
|
How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak) by ev_motors » Sat, 2018-04-28 10:18 |
0 |
by ev_motors Sat, 2018-04-28 10:18 |
|
|
Help with FOC/PID parameter by CTSchorsch » Thu, 2020-01-23 21:57 |
0 |
by CTSchorsch Thu, 2020-01-23 21:57 |
|
|
Problems with UART communication via Arduino UNO by Michael Hamm » Fri, 2022-02-04 13:29 |
0 |
by Michael Hamm Fri, 2022-02-04 13:29 |
|
|
GT2 Remote to Vesc connection issue by tom.embke » Tue, 2018-05-01 14:41 |
0 |
by tom.embke Tue, 2018-05-01 14:41 |
|
|
CAN eRPM report by alxsfrm » Mon, 2022-02-07 11:01 |
0 |
by alxsfrm Mon, 2022-02-07 11:01 |
|
|
Trying to read and set MCCONF by Jamie42 » Tue, 2020-03-24 19:47 |
0 |
by Jamie42 Tue, 2020-03-24 19:47 |
|
|
can not start motor with high duty by qdxiatao » Sat, 2018-03-24 03:58 |
0 |
by qdxiatao Sat, 2018-03-24 03:58 |
Log in to post new content in the forum.
