You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC 60 75 IMU by Alistair Goodman » Thu, 2025-08-14 18:23 |
0 |
by Alistair Goodman Thu, 2025-08-14 18:23 |
|
|
Forward/brake/reverse mode? by RDN2003 » Thu, 2019-10-03 02:13 |
6 |
by tokerodev Thu, 2025-08-21 13:55 |
|
|
VESC PAS and ADC App - How does it work? by numbke » Fri, 2023-02-24 23:49 |
11 |
by Brett.W Fri, 2025-08-22 16:46 |
|
|
How deactivate Cruise Control vithout button? It is posible deactivate with 2 pin brake sensor or brake throttle? by denon480 » Fri, 2025-08-22 18:22 |
0 |
by denon480 Fri, 2025-08-22 18:25 |
|
|
Which App to use and how to wire it by philboslaggins » Sat, 2022-11-05 16:20 |
2 |
by nando Fri, 2025-08-29 15:19 |
|
|
VescTool version 6.06 Android latest update by Brice77 » Sun, 2025-08-31 17:24 |
2 |
by Brice77 Mon, 2025-09-01 23:55 |
|
|
3 shunt low side vs 3 shunt 'in phase' current sensing by ripperpc » Mon, 2020-05-04 08:47 |
7 |
by Serhii Diahlev Thu, 2025-09-04 14:11 |
|
|
Will the new VESC company have plans related to robotics applications? by radish » Fri, 2025-09-05 13:14 |
1 |
by radish Fri, 2025-09-05 13:20 |
|
|
Vesc tool apk by gswskog » Fri, 2025-09-05 18:02 |
0 |
by gswskog Fri, 2025-09-05 18:02 |
|
|
RPi 5 and VESC over UART by XAQ » Wed, 2025-09-10 07:27 |
0 |
by XAQ Wed, 2025-09-10 19:33 |
|
|
Flipsky FSV 6.6 no longer working with new VESC Tool by oliver1998 » Fri, 2025-09-12 06:06 |
0 |
by oliver1998 Fri, 2025-09-12 06:06 |
|
|
Can't use the BLDC controller by hugog » Mon, 2025-09-08 12:00 |
6 |
by electricfox Fri, 2025-09-12 08:34 |
|
|
VESC with Python on a RPi 5 by XAQ » Mon, 2025-09-15 01:06 |
0 |
by XAQ Mon, 2025-09-15 01:06 |
|
|
Unstable current readings over VESC CAN (UART/USB are fine) by vukstijepovic » Mon, 2025-09-15 16:59 |
0 |
by vukstijepovic Mon, 2025-09-15 16:59 |
|
|
Dual VESC Controller - Internal CAN Forwarding Failure -NOW WITH CODE EXAMPLE ;) by XAQ » Mon, 2025-09-15 07:52 |
0 |
by XAQ Mon, 2025-09-15 17:42 |
|
|
2 Speed ADC control by totalgeek9224 » Mon, 2025-09-22 19:47 |
0 |
by totalgeek9224 Mon, 2025-09-22 19:47 |
|
|
Help Setup Flipsky FSESC 4.12 by R66 » Mon, 2025-09-29 05:23 |
1 |
by R66 Mon, 2025-09-29 06:58 |
|
|
Help - physical switch to change profiles on ADC15 by SwissCanuck » Sun, 2025-10-05 13:59 |
0 |
by SwissCanuck Sun, 2025-10-05 13:59 |
|
|
Problem with Android app by Er-Chispa » Wed, 2025-10-08 20:58 |
0 |
by Er-Chispa Wed, 2025-10-08 21:02 |
|
|
FSESC 75350 UNBALANCED_CURRENTS fault at higher loads by colmor » Thu, 2025-05-01 01:21 |
1 |
by erider Thu, 2025-10-09 07:55 |
|
|
VESC OpenLoop for didactic application by dpeinado » Tue, 2022-07-12 12:32 |
3 |
by Alexander470815 Sun, 2025-10-12 18:38 |
|
|
Custom-made VESC PCB: High current sensor offset/Overcurrent fault during motor detection, possible hardware/firmware mismatch by Chinmay Mulgund » Mon, 2025-10-13 13:56 |
0 |
by Chinmay Mulgund Mon, 2025-10-13 14:02 |
|
|
About How to control the "FLIPSKY Dual FSESC6.7 PLUS" by tonyH » Tue, 2025-10-14 11:35 |
0 |
by tonyH Tue, 2025-10-14 11:35 |
|
|
Charging Li-ion battery using the VESC Harmony 32S BMS by sainihalj » Tue, 2025-10-14 14:42 |
0 |
by sainihalj Tue, 2025-10-14 14:42 |
|
|
tuning low kv high pole sensorless outrunner by cdlapoin » Tue, 2025-05-20 22:14 |
1 |
by dpaschall Wed, 2025-10-15 07:46 |
Log in to post new content in the forum.
