You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Flipsky6.6 usb not detected This topic has been moved to "Third Party Hardware" (View topic) |
|||
|
Error code 6 by PatWhite32 » Mon, 2023-06-19 23:15 |
0 |
by PatWhite32 Mon, 2023-06-19 23:15 |
|
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 » Wed, 2023-04-12 16:28 |
0 |
by Tom65 Wed, 2023-04-12 16:28 |
|
|
current measurements crazy high after replacing DRV8301 with DRV8302, it throws a FAULT_CODE_ABS_OVER_CURRENT by idkanythinggoes » Thu, 2021-03-18 04:34 |
0 |
by idkanythinggoes Thu, 2021-03-18 04:34 |
|
|
4.12 cooling mod by thewho » Wed, 2019-05-01 18:45 |
0 |
by thewho Wed, 2019-05-01 18:45 |
|
|
Can someone verify this by jsbenson » Mon, 2023-06-26 09:22 |
0 |
by jsbenson Tue, 2023-06-27 07:50 |
|
|
Position Limits w/ BDC and ABI Encoder by gokulswami » Thu, 2023-04-13 10:43 |
0 |
by gokulswami Thu, 2023-04-13 10:43 |
|
|
VESC 6: frequent direction change application problem by cromoly » Thu, 2019-05-02 01:45 |
0 |
by cromoly Thu, 2019-05-02 01:45 |
|
|
Motors spin during detection but then won't spin by jsbenson » Tue, 2023-06-27 23:54 |
0 |
by jsbenson Tue, 2023-06-27 23:54 |
|
|
Minimum speed push cart using arduino by BarBumble » Wed, 2021-05-12 09:29 |
0 |
by BarBumble Wed, 2021-05-12 09:29 |
|
|
VESC6 cooked MOSFET by hagoston » Mon, 2021-03-22 14:23 |
0 |
by hagoston Mon, 2021-03-22 15:03 |
|
|
RPM Control Problems by MrMonk3y » Mon, 2019-05-06 22:54 |
0 |
by MrMonk3y Mon, 2019-05-06 22:54 |
|
|
12v(3s) Input to VESC 75/250 by AliBarrett10 » Wed, 2021-03-24 14:36 |
0 |
by AliBarrett10 Wed, 2021-03-24 16:19 |
|
|
Bench Testing by usaevo7 » Tue, 2023-04-25 16:50 |
0 |
by usaevo7 Tue, 2023-04-25 16:50 |
|
|
NRF Implementation by Christian » Thu, 2018-02-15 14:36 |
0 |
by Christian Thu, 2018-02-15 14:36 |
|
|
120V dual VESC for E-scooter by Daniel Kaminski » Sun, 2021-03-28 12:43 |
0 |
by Daniel Kaminski Sun, 2021-03-28 12:43 |
|
|
Master Slave Controller for Motor by Blemot » Tue, 2019-03-19 09:46 |
0 |
by Blemot Tue, 2019-03-19 09:46 |
|
|
DUAL VESC FOR BIDIRECTIONAL ROTATION by Khaliduzzaman Mredul » Fri, 2023-05-05 06:46 |
0 |
by Khaliduzzaman Mredul Fri, 2023-05-05 11:00 |
|
|
Storing VESC Tool data for later analysis by AidanNowa » Wed, 2024-06-12 15:57 |
0 |
by AidanNowa Wed, 2024-06-12 15:57 |
|
|
Servo Mode / ODrive on VESC by JulianT » Tue, 2020-02-04 09:19 |
0 |
by JulianT Tue, 2020-02-04 09:19 |
|
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
|
Large robot servo controller with VESC, how to set up position control by kisdia » Thu, 2024-09-19 17:47 |
0 |
by kisdia Thu, 2024-09-19 17:47 |
|
|
Can't Update Firmware by indianboy42 » Mon, 2024-06-17 08:54 |
0 |
by indianboy42 Mon, 2024-06-17 08:54 |
|
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 » Fri, 2020-04-10 12:33 |
0 |
by olaf2273 Mon, 2020-04-27 15:34 |
|
|
Firmware V4.00 field oriented control motor jerk but wont spin by jordanlow » Thu, 2020-02-13 14:41 |
0 |
by jordanlow Thu, 2020-02-13 14:41 |
|
Log in to post new content in the forum.
