You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Low torque at 0 RPM by ivan_osyotr » Sat, 2024-06-01 18:37 |
0 |
by ivan_osyotr Sat, 2024-06-01 18:37 |
|
|
VESC 4.12 Current limit question by jamesk18@vt.edu » Tue, 2024-03-26 18:30 |
0 |
by jamesk18@vt.edu Tue, 2024-03-26 18:30 |
|
|
The rpm control is not working properly by ptss37 » Wed, 2021-11-24 03:30 |
0 |
by ptss37 Wed, 2021-11-24 03:44 |
|
|
Upgrading to higher voltage setup by JPK2 » Wed, 2024-06-05 22:11 |
0 |
by JPK2 Wed, 2024-06-05 22:11 |
|
|
Any issues with the DRV8323? by shaman » Thu, 2019-10-24 21:50 |
0 |
by shaman Thu, 2019-10-24 21:50 |
|
|
VESC 6 Mk IV Phase 1 Current Double Others by bayetan » Mon, 2024-01-29 16:13 |
0 |
by bayetan Mon, 2024-01-29 16:13 |
|
|
No power by ika12 » Tue, 2024-04-02 21:46 |
0 |
by ika12 Tue, 2024-04-02 21:46 |
|
|
How to set up RF receiver for PPM or UART input? by adamdorr » Tue, 2020-01-07 16:23 |
0 |
by adamdorr Tue, 2020-01-07 16:23 |
|
|
2kW motor with VESS 75200 by Sazabi » Fri, 2024-04-05 11:17 |
0 |
by Sazabi Fri, 2024-04-05 11:18 |
|
|
Dutycyle dropping under load by Julzz112 » Sun, 2024-04-14 18:31 |
0 |
by Julzz112 Tue, 2024-04-16 08:26 |
|
|
resistance and inductance value changes when each measurement by alexshen2012 » Fri, 2022-07-01 05:42 |
0 |
by alexshen2012 Fri, 2022-07-01 05:42 |
|
|
Duty vs RPM for smooth start and slow running by Davideo » Tue, 2018-04-24 14:42 |
0 |
by Davideo Tue, 2018-04-24 14:42 |
|
|
MakerX-FOC DV6s PWM for 2 BLDC Motors by paulsimpsonii » Tue, 2026-03-03 18:08 |
0 |
by paulsimpsonii Tue, 2026-03-03 18:08 |
|
|
VESC custom firmware custom UART message by steveyplst » Tue, 2020-08-04 10:23 |
0 |
by steveyplst Tue, 2020-08-04 10:23 |
|
|
The controller is not responding by TheJuan901 » Sat, 2026-03-14 02:03 |
0 |
by TheJuan901 Sat, 2026-03-14 02:03 |
|
|
Flipsky FSV 6.6 no longer working with new VESC Tool by oliver1998 » Fri, 2025-09-12 06:06 |
0 |
by oliver1998 Fri, 2025-09-12 06:06 |
|
|
Dultron X2 UP by timgunn5555 » Wed, 2026-03-18 02:34 |
0 |
by timgunn5555 Wed, 2026-03-18 02:34 |
|
|
Dual VESC Controller - Internal CAN Forwarding Failure -NOW WITH CODE EXAMPLE ;) by XAQ » Mon, 2025-09-15 07:52 |
0 |
by XAQ Mon, 2025-09-15 17:42 |
|
|
vesc6 limitations by badger1666 » Sat, 2018-04-28 19:20 |
0 |
by badger1666 Sat, 2018-04-28 19:20 |
|
|
2 Speed ADC control by totalgeek9224 » Mon, 2025-09-22 19:47 |
0 |
by totalgeek9224 Mon, 2025-09-22 19:47 |
|
|
VESC specialist required. by BlackPanthera » Mon, 2022-07-18 17:11 |
0 |
by BlackPanthera Mon, 2022-07-18 17:11 |
|
|
connecting vesc tool with Prototipo by Govert » Thu, 2020-07-02 19:43 |
0 |
by Govert Thu, 2020-07-02 19:43 |
|
|
Voltage Calibration by Frantin » Mon, 2026-04-20 21:40 |
0 |
by Frantin Mon, 2026-04-20 21:40 |
|
|
How do you turn on traction control ( I can't remember) by msim2 » Fri, 2022-05-20 22:06 |
0 |
by msim2 Fri, 2022-05-20 22:06 |
|
|
VESC 6 Mark III and Traxxas Summit Radio Receiver PWM / PPM Signals by j98221@gmail.com » Fri, 2020-07-03 07:27 |
0 |
by j98221@gmail.com Fri, 2020-07-03 07:27 |
Log in to post new content in the forum.
