You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC appears to loose sync when increasing throttle by srinath » Sun, 2023-06-04 04:11 |
0 |
by srinath Sun, 2023-06-04 04:11 |
|
|
Changing the timer for VESC auto turn off timing by dsuresh » Mon, 2021-03-15 21:19 |
0 |
by dsuresh Mon, 2021-03-15 21:19 |
|
|
No load FOC stops when full FWD throttle. by toboli » Mon, 2023-06-05 18:41 |
0 |
by toboli Mon, 2023-06-05 18:41 |
|
|
No sensers by Phill Dixon » Thu, 2024-10-24 18:58 |
0 |
by Phill Dixon Thu, 2024-10-24 18:58 |
|
|
General help by jskessel » Tue, 2024-07-16 20:09 |
0 |
by jskessel Tue, 2024-07-16 20:09 |
|
|
VESC 6.6 vs. MK5 vs. MK6 by jejaj25773 » Sat, 2024-07-27 02:37 |
0 |
by jejaj25773 Sat, 2024-07-27 02:37 |
|
|
Help with FOC/PID parameter by CTSchorsch » Thu, 2020-01-23 21:57 |
0 |
by CTSchorsch Thu, 2020-01-23 21:57 |
|
|
Problems with UART communication via Arduino UNO by Michael Hamm » Fri, 2022-02-04 13:29 |
0 |
by Michael Hamm Fri, 2022-02-04 13:29 |
|
|
Flipsky Mini Dual FSESC4.20+voyager remote+tankmode by allan_overbye » Fri, 2024-11-08 14:13 |
0 |
by allan_overbye Fri, 2024-11-08 14:13 |
|
|
CAN eRPM report by alxsfrm » Mon, 2022-02-07 11:01 |
0 |
by alxsfrm Mon, 2022-02-07 11:01 |
|
|
Trying to read and set MCCONF by Jamie42 » Tue, 2020-03-24 19:47 |
0 |
by Jamie42 Tue, 2020-03-24 19:47 |
|
|
Motor won't hold constant speed by Groundspeed100 » Thu, 2024-11-14 05:33 |
0 |
by Groundspeed100 Thu, 2024-11-14 05:33 |
|
|
4 fried vesc's Australia by adamclarke1985 » Tue, 2020-03-31 20:48 |
0 |
by adamclarke1985 Tue, 2020-03-31 21:24 |
|
|
Use IMU for keeping direction by arnolde » Mon, 2024-11-25 11:12 |
0 |
by arnolde Mon, 2024-11-25 11:19 |
|
|
Storing VESC Tool data for later analysis by AidanNowa » Wed, 2024-06-12 15:57 |
0 |
by AidanNowa Wed, 2024-06-12 15:57 |
|
|
Servo Mode / ODrive on VESC by JulianT » Tue, 2020-02-04 09:19 |
0 |
by JulianT Tue, 2020-02-04 09:19 |
|
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
|
Large robot servo controller with VESC, how to set up position control by kisdia » Thu, 2024-09-19 17:47 |
0 |
by kisdia Thu, 2024-09-19 17:47 |
|
|
Can't Update Firmware by indianboy42 » Mon, 2024-06-17 08:54 |
0 |
by indianboy42 Mon, 2024-06-17 08:54 |
|
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 » Fri, 2020-04-10 12:33 |
0 |
by olaf2273 Mon, 2020-04-27 15:34 |
|
|
Firmware V4.00 field oriented control motor jerk but wont spin by jordanlow » Thu, 2020-02-13 14:41 |
0 |
by jordanlow Thu, 2020-02-13 14:41 |
|
|
Maximum Motor RPM will not reached by Skyver » Sun, 2022-01-23 10:53 |
0 |
by Skyver Sun, 2022-01-23 10:53 |
|
|
Running PID position Control with FOC sensorless by talabo » Fri, 2021-12-03 17:21 |
0 |
by talabo Fri, 2021-12-03 17:21 |
|
|
Connecting AMT203 to Flipsky 4.20 ESC by kgeo0003 » Mon, 2022-01-24 06:44 |
0 |
by kgeo0003 Mon, 2022-01-24 09:00 |
|
|
Autonomous RC car with Focbox suddenly stops by Autocar » Mon, 2021-12-06 06:55 |
0 |
by Autocar Mon, 2021-12-06 06:55 |
Log in to post new content in the forum.
