You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Why is the speed lower in FOC mode than BLDC mode ? by stone_1706 » Thu, 2019-01-17 08:23 |
8 |
by speed3r Wed, 2022-06-15 09:34 |
|
|
5phase Vesc based on 75/300 by BartE » Thu, 2020-03-05 23:17 |
8 |
by vadicus Sun, 2020-03-08 05:51 |
|
|
Connect 4 vesc with can-bus, motors stuttering by oyvinla » Tue, 2022-01-04 17:12 |
8 |
by ahanktcd Wed, 2024-04-17 06:35 |
|
|
Tell me how to accurately determine the type of engine FOC, BLDC by Valera1996 » Sun, 2020-02-09 18:53 |
8 |
by vadicus Mon, 2020-02-17 22:41 |
|
|
Is this kogging and jitter in low rpms expected? by Snabelost » Sat, 2022-10-22 16:53 |
8 |
by Snabelost Fri, 2022-10-28 16:07 |
|
|
VESC Battery Packs by frank » Tue, 2020-10-13 15:21 |
8 |
by zhivko Sat, 2024-08-10 21:14 |
|
|
VESC as Generator - Low Output at High Brake Current? by hoeken » Sat, 2021-08-28 17:42 |
8 |
by flydr2 Wed, 2023-04-12 20:38 |
|
|
Is there a VESC with the form factor like a Votol EM200 ? (with those threaded lugs|Screw Terminals)) by Gatze » Sat, 2022-03-12 09:33 |
8 |
by qdxiatao Sat, 2022-08-20 04:09 |
|
|
Newbie Help - ADC input by nickyg » Tue, 2020-04-28 11:05 |
8 |
by velolac Fri, 2021-12-10 19:40 |
|
|
Difference between the current, duty cycle and PID speed control mode by tromes » Thu, 2020-06-11 07:51 |
8 |
by Onarb Kabr Wed, 2025-01-15 13:32 |
|
|
Vesc 100/250 (Trampa board) wiring for ebike by Oded Mazor » Fri, 2022-03-18 23:34 |
8 |
by Markula Fri, 2022-04-01 09:21 |
|
|
highest battery current with 6.6? by devin » Tue, 2020-01-14 16:05 |
9 |
by devin Wed, 2020-01-15 01:05 |
|
|
VESC recommendation for sailboat conversion by Henque19 » Thu, 2019-11-28 00:42 |
9 |
by Henque19 Fri, 2019-12-20 16:15 |
|
|
ERPM to Rpm by faheemift » Wed, 2021-03-31 11:11 |
9 |
by faheemift Wed, 2021-04-14 13:01 |
|
|
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON » Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
|
|
Problem with Bluetooth connection (HM-10) by squdowx » Mon, 2018-07-30 15:56 |
9 |
by CTSchorsch Thu, 2019-12-05 21:27 |
|
|
VESC with Raspberry Pi 3 by Antonio Rodrígu... » Sun, 2018-06-03 18:54 |
9 |
by ShortCircuit Thu, 2018-06-28 15:33 |
|
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 » Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
|
|
Trampa VESC 100/250 suitable for heavy applications? by nojjan » Thu, 2022-12-29 13:52 |
9 |
by vadicus Wed, 2023-03-01 06:26 |
|
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker » Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
|
|
Noise with Hall sensor at high speed by yosoufe » Thu, 2018-03-08 12:34 |
9 |
by yosoufe Tue, 2018-03-20 09:30 |
|
|
Failure in Motor Set Up by Toshi Sharma » Tue, 2022-01-11 15:19 |
9 |
by frank Thu, 2022-01-13 14:15 |
|
|
Acceleration control to desired RPM by bjohns » Fri, 2018-07-20 22:08 |
9 |
by arvidb Thu, 2018-08-09 21:15 |
|
|
Braking in speed PID controlled mode by vadimz » Sat, 2018-09-15 14:19 |
9 |
by zybyxutese Mon, 2019-04-01 13:35 |
|
|
Motor braking - shorting phases by rok340 » Thu, 2021-01-21 07:49 |
9 |
by dpeinado Mon, 2022-02-14 12:36 |
Log in to post new content in the forum.
