You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Control type = Current No Reverse With Brake by perpetum » Mon, 2020-11-02 05:00 |
0 |
by perpetum Mon, 2020-11-02 05:00 |
|
|
help needed with raptor 2 remote by dave9401 » Mon, 2020-11-02 10:26 |
0 |
by dave9401 Mon, 2020-11-02 10:26 |
|
|
"Throttle" help by benha » Wed, 2019-08-07 05:58 |
0 |
by benha Wed, 2019-08-07 05:58 |
|
|
Dual motor setup for Turnigy SK8 V2 60A x 2 3~12S Twin Motor Skateboard ESC? by fil02184 » Tue, 2022-10-18 04:07 |
0 |
by fil02184 Tue, 2022-10-18 16:00 |
|
|
Flipsky VESC 4.20 with 5.1 Firmware PWM input offset by mantisrobot » Thu, 2020-11-05 12:24 |
0 |
by mantisrobot Thu, 2020-11-05 12:24 |
|
|
Simulating controller accurately by TechAUmNu » Fri, 2019-08-16 15:35 |
0 |
by TechAUmNu Fri, 2019-08-16 15:35 |
|
|
Porting VESC to STML4 by Vince_1618 » Fri, 2022-10-28 14:01 |
0 |
by Vince_1618 Fri, 2022-10-28 14:01 |
|
|
HFI optimisation with increase in switching frequency by rainebk@bigpond... » Tue, 2022-09-13 06:53 |
0 |
by rainebk@bigpond... Tue, 2022-09-13 06:53 |
|
|
VESC Wand shows INF and 100% Batt by BLKFLD » Sat, 2020-09-26 04:48 |
0 |
by BLKFLD Sat, 2020-09-26 04:48 |
|
|
Tuning process? by wingborne » Tue, 2020-09-29 00:09 |
0 |
by wingborne Tue, 2020-09-29 21:39 |
|
|
foc with encoder fails to run smoothly by jdn » Thu, 2019-08-22 12:26 |
0 |
by jdn Thu, 2019-08-22 15:47 |
|
|
Implementing developer tools and PID tuning by nowholeself » Wed, 2020-10-07 07:04 |
0 |
by nowholeself Wed, 2020-10-07 07:04 |
|
|
power limited??? by ka_ru » Tue, 2020-11-24 13:53 |
0 |
by ka_ru Tue, 2020-11-24 13:53 |
|
|
How to Write Serial Communication Program Not Applicable to RTOS by Jack_Li » Fri, 2019-07-05 06:55 |
0 |
by Jack_Li Fri, 2019-07-05 06:58 |
|
|
-solved- by KittenDude » Sat, 2020-11-28 06:30 |
0 |
by KittenDude Sun, 2020-11-29 19:27 |
|
|
Reverse and brake inputs? by hackish » Sat, 2019-09-07 19:20 |
0 |
by hackish Sat, 2019-09-07 19:20 |
|
|
VESC to test e-Bike motor and car alternator as Torque Load..? by arifbustani » Thu, 2019-09-12 19:00 |
0 |
by arifbustani Thu, 2019-09-12 19:00 |
|
|
How to tune BLDC delay mode by Torbjorn » Tue, 2022-11-15 13:21 |
0 |
by Torbjorn Tue, 2022-11-15 13:21 |
|
|
Current loop resonance in higher ERPM under Current Mode by ypl » Sat, 2019-07-20 09:34 |
0 |
by ypl Sat, 2019-07-20 09:34 |
|
|
Install VESC on ubuntu 18.04 bionic by rest_vesc_001 » Tue, 2020-12-08 07:32 |
0 |
by rest_vesc_001 Fri, 2020-12-11 15:15 |
|
|
Are vescs reliable? thinking about getting by jon218white » Mon, 2020-10-26 19:15 |
0 |
by jon218white Mon, 2020-10-26 19:17 |
|
|
Power Switch by flyingbrike » Wed, 2021-09-08 13:47 |
0 |
by flyingbrike Wed, 2021-09-08 13:47 |
|
|
Flipsky hall sensors by alanrooks007 » Sat, 2021-06-26 00:55 |
0 |
by alanrooks007 Sat, 2021-06-26 00:55 |
|
|
Is there a way to temporarily disable kill switch by Elliott Wolbach » Mon, 2023-07-31 23:21 |
0 |
by Elliott Wolbach Mon, 2023-07-31 23:21 |
|
|
48N32P sync loss by roque.canales » Fri, 2023-08-18 11:01 |
0 |
by roque.canales Fri, 2023-08-18 11:01 |
Log in to post new content in the forum.
