You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
bldc motor detection with Focbox and 190kv motor by gicho » Mon, 2018-01-15 23:04 |
1 |
by linsus Wed, 2018-01-17 10:23 |
|
|
bootloader destroied by notger » Tue, 2017-09-19 19:55 |
3 |
by dinamee Sat, 2018-01-13 10:09 |
|
|
FOC and extremely low speeds do not look sinusoidal by wdaehn » Wed, 2017-11-29 21:33 |
11 |
by Benjamin Mahony Wed, 2018-01-10 01:19 |
|
|
Motor rotation direction by e-biker » Fri, 2017-12-22 15:02 |
2 |
by e-biker Tue, 2018-01-02 13:15 |
|
|
Positional Control, Hall Sensor by wdaehn » Fri, 2017-12-08 15:02 |
4 |
by wdaehn Mon, 2017-12-25 09:46 |
|
|
Merry Christmas! by frank » Fri, 2017-12-22 14:31 |
4 |
by ThierryGTLTS Sun, 2017-12-24 14:34 |
|
|
Two Motors on same Shaft by Giga93 » Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
|
|
trampa by badger1666 » Mon, 2017-12-11 22:37 |
5 |
by wdaehn Wed, 2017-12-13 12:17 |
|
|
MOSFET driver delay compensation by e-biker » Sun, 2017-12-10 16:21 |
2 |
by e-biker Tue, 2017-12-12 09:41 |
|
|
Minimum speed by Davideo » Sat, 2017-10-21 17:40 |
7 |
by Davideo Thu, 2017-12-07 00:18 |
|
|
Hub Motor Remote Control by bf01 » Tue, 2017-11-14 16:04 |
3 |
by frank Wed, 2017-12-06 23:41 |
|
|
RPM measurement. by Roger Wolff » Wed, 2017-11-29 16:48 |
2 |
by Roger Wolff Fri, 2017-12-01 06:25 |
|
|
Using vesc for Position and driving my BB8 Robot by Quicksilverstar » Wed, 2017-11-15 19:25 |
4 |
by Quicksilverstar Sat, 2017-11-25 16:11 |
|
|
about reference hardware by qdxiatao » Mon, 2017-09-25 08:32 |
10 |
by lizardmech Tue, 2017-11-21 19:40 |
|
|
Charge wires by Phill Dixon » Tue, 2017-10-24 14:24 |
4 |
by linsus Tue, 2017-11-21 14:39 |
|
|
Battery power by Phill Dixon » Tue, 2017-11-14 20:14 |
4 |
by slapshot136 Tue, 2017-11-21 05:01 |
|
|
Question about improvement og VESC 6.4 by StreetSkater » Sat, 2017-11-18 08:03 |
1 |
by Roger Wolff Sat, 2017-11-18 12:01 |
|
|
At standstill a 30A limit? by Roger Wolff » Fri, 2017-11-17 09:37 |
2 |
by Roger Wolff Sat, 2017-11-18 11:58 |
|
|
ws8212 and VESC firmware by dannlh » Fri, 2017-11-03 04:17 |
2 |
by dannlh Sat, 2017-11-04 18:47 |
|
|
VESC 6 motor setup: Resistance measurement jumps by thomasjfox » Mon, 2017-10-09 20:42 |
2 |
by thomasjfox Sat, 2017-10-28 21:57 |
|
|
search by forum by aysubscriber@ic... » Fri, 2017-10-06 20:39 |
6 |
by aysubscriber@ic... Mon, 2017-10-23 16:06 |
|
|
Ideal Thermistor/Temperature Sensor? by josh » Sat, 2017-10-14 07:07 |
3 |
by josh Sun, 2017-10-22 06:52 |
|
|
What do you need on your computer to run the vesc tool by Phill Dixon » Wed, 2017-10-04 21:00 |
2 |
by Tampaesk8er Wed, 2017-10-18 23:22 |
|
|
Can someone help me understand why I've burned up a DRV8302 in less than 10 seconds? by shimdidly » Fri, 2017-10-13 02:01 |
3 |
by shimdidly Mon, 2017-10-16 17:13 |
|
|
version of the vesc tool by aysubscriber@ic... » Tue, 2017-10-03 07:53 |
4 |
by aysubscriber@ic... Fri, 2017-10-13 03:47 |
Log in to post new content in the forum.
