You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
advice on position control by feskarn » Mon, 2021-02-15 14:47 |
0 |
by feskarn Mon, 2021-02-15 14:47 |
|
|
How to reboot VESC from serial port by Ivko » Mon, 2021-01-04 18:44 |
0 |
by Ivko Mon, 2021-01-04 18:44 |
|
|
AS5047 over SPI pins on VESC six by Jessica » Fri, 2018-12-21 11:10 |
0 |
by Jessica Fri, 2018-12-21 11:10 |
|
|
Can bus communication. by Piamen » Wed, 2019-11-27 06:47 |
0 |
by Piamen Wed, 2019-11-27 06:47 |
|
|
Setting the motor parameters by Lenar » Sat, 2024-05-04 10:18 |
0 |
by Lenar Sat, 2024-05-04 10:18 |
|
|
Battery percentage mapping by Sharkboy » Mon, 2024-05-06 22:55 |
0 |
by Sharkboy Mon, 2024-05-06 22:55 |
|
|
Runtime motor control with CAN by Davidepolpi91 » Fri, 2024-03-15 15:12 |
0 |
by Davidepolpi91 Fri, 2024-03-15 15:12 |
|
|
Flysky FESC 6.7 to disable 5V by AryehChen » Wed, 2024-05-15 18:44 |
0 |
by AryehChen Wed, 2024-05-15 18:46 |
|
|
noob with so many setup/wiring questions...... by flez1966 » Sun, 2024-03-17 20:17 |
0 |
by flez1966 Sun, 2024-03-17 20:17 |
|
|
Unofficial VESC Discord server by kubark42 » Tue, 2021-11-16 16:07 |
0 |
by kubark42 Fri, 2021-11-19 03:12 |
|
|
Reading COMM packets through CAN. by 1423rj » Mon, 2024-05-20 08:22 |
0 |
by 1423rj Mon, 2024-05-20 08:23 |
|
|
Reverse indicator by bmblank » Wed, 2024-03-20 20:41 |
0 |
by bmblank Wed, 2024-03-20 20:41 |
|
|
DRV8302 Gate Pin output waveform is abnormal by yandongyu1998 » Fri, 2019-12-13 07:21 |
0 |
by yandongyu1998 Fri, 2019-12-13 07:21 |
|
|
Low torque at 0 RPM by ivan_osyotr » Sat, 2024-06-01 18:37 |
0 |
by ivan_osyotr Sat, 2024-06-01 18:37 |
|
|
VESC 4.12 Current limit question by jamesk18@vt.edu » Tue, 2024-03-26 18:30 |
0 |
by jamesk18@vt.edu Tue, 2024-03-26 18:30 |
|
|
The rpm control is not working properly by ptss37 » Wed, 2021-11-24 03:30 |
0 |
by ptss37 Wed, 2021-11-24 03:44 |
|
|
Dollar signs break private messages by TechAUmNu » Tue, 2018-04-24 18:09 |
0 |
by TechAUmNu Tue, 2018-04-24 18:09 |
|
|
Upgrading to higher voltage setup by JPK2 » Wed, 2024-06-05 22:11 |
0 |
by JPK2 Wed, 2024-06-05 22:11 |
|
|
Any issues with the DRV8323? by shaman » Thu, 2019-10-24 21:50 |
0 |
by shaman Thu, 2019-10-24 21:50 |
|
|
VESC 6 Mk IV Phase 1 Current Double Others by bayetan » Mon, 2024-01-29 16:13 |
0 |
by bayetan Mon, 2024-01-29 16:13 |
|
|
How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak) by ev_motors » Sat, 2018-04-28 10:18 |
0 |
by ev_motors Sat, 2018-04-28 10:18 |
|
|
No power by ika12 » Tue, 2024-04-02 21:46 |
0 |
by ika12 Tue, 2024-04-02 21:46 |
|
|
How to set up RF receiver for PPM or UART input? by adamdorr » Tue, 2020-01-07 16:23 |
0 |
by adamdorr Tue, 2020-01-07 16:23 |
|
|
2kW motor with VESS 75200 by Sazabi » Fri, 2024-04-05 11:17 |
0 |
by Sazabi Fri, 2024-04-05 11:18 |
|
|
GT2 Remote to Vesc connection issue by tom.embke » Tue, 2018-05-01 14:41 |
0 |
by tom.embke Tue, 2018-05-01 14:41 |
Log in to post new content in the forum.
