You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Vesc boost charging with external inductors by Bunda » Wed, 2025-10-29 08:37 |
0 |
by Bunda Wed, 2025-10-29 08:38 |
|
|
Auxiliary Output Mode pin# by garyp » Sat, 2020-08-22 18:17 |
0 |
by garyp Sat, 2020-08-22 18:17 |
|
|
wont gonnect by rustman01 » Wed, 2025-11-05 19:26 |
0 |
by rustman01 Wed, 2025-11-05 19:26 |
|
|
How to Write Serial Communication Program Not Applicable to RTOS by Jack_Li » Fri, 2019-07-05 06:55 |
0 |
by Jack_Li Fri, 2019-07-05 06:58 |
|
|
VESC Replacing Shunt Resistor with Hall Current Sensor？ by happy85 » Fri, 2025-07-18 06:21 |
0 |
by happy85 Fri, 2025-07-18 11:51 |
|
|
Reverse and brake inputs? by hackish » Sat, 2019-09-07 19:20 |
0 |
by hackish Sat, 2019-09-07 19:20 |
|
|
Motor "sticks" and stops spinning by flagoworld » Fri, 2025-12-05 19:03 |
0 |
by flagoworld Fri, 2025-12-05 19:03 |
|
|
Motor runs heavy in one direction, light in the other / No speed in realtime interface / Correct phase & hall wiring? by pcace » Sat, 2025-07-26 08:00 |
0 |
by pcace Sat, 2025-07-26 08:00 |
|
|
VESC to test e-Bike motor and car alternator as Torque Load..? by arifbustani » Thu, 2019-09-12 19:00 |
0 |
by arifbustani Thu, 2019-09-12 19:00 |
|
|
Limit Max RPM on a Brushed Motor in DC Mode by KirkusMaximus » Fri, 2020-09-04 02:52 |
0 |
by KirkusMaximus Fri, 2020-09-04 02:58 |
|
|
Current loop resonance in higher ERPM under Current Mode by ypl » Sat, 2019-07-20 09:34 |
0 |
by ypl Sat, 2019-07-20 09:34 |
|
|
ignore this by tobe81cwb » Tue, 2022-06-21 18:51 |
0 |
by tobe81cwb Tue, 2022-07-19 16:44 |
|
|
High res ABI encoder on Vesc not working by JH » Sun, 2026-01-25 01:23 |
0 |
by JH Sun, 2026-01-25 01:23 |
|
|
USB port connection error VESC 6 MkVI by LeeJeonghyeon » Wed, 2025-08-13 17:07 |
0 |
by LeeJeonghyeon Wed, 2025-08-13 17:07 |
|
|
CAN Analyzer by min » Tue, 2022-05-03 10:38 |
0 |
by min Tue, 2022-05-03 10:38 |
|
|
Set current - is it input or phase current? by aegidius » Sun, 2026-02-08 05:58 |
0 |
by aegidius Sun, 2026-02-08 05:58 |
|
|
How deactivate Cruise Control vithout button? It is posible deactivate with 2 pin brake sensor or brake throttle? by denon480 » Fri, 2025-08-22 18:22 |
0 |
by denon480 Fri, 2025-08-22 18:25 |
|
|
VESC with no working brake button by tavsanist » Sat, 2019-07-27 02:40 |
0 |
by tavsanist Sat, 2019-07-27 02:40 |
|
|
resistance and inductance value changes when each measurement by alexshen2012 » Fri, 2022-07-01 05:45 |
0 |
by alexshen2012 Fri, 2022-07-01 05:45 |
|
|
Noise related issues? by RDN2003 » Sun, 2020-07-26 20:17 |
0 |
by RDN2003 Sun, 2020-07-26 20:17 |
|
|
KERS system with a VESC 100/250 MKIII by Simone Succi » Thu, 2026-02-26 08:28 |
0 |
by Simone Succi Thu, 2026-02-26 16:20 |
|
|
Vesc tool apk by gswskog » Fri, 2025-09-05 18:02 |
0 |
by gswskog Fri, 2025-09-05 18:02 |
|
|
RPi 5 and VESC over UART by XAQ » Wed, 2025-09-10 07:27 |
0 |
by XAQ Wed, 2025-09-10 19:33 |
|
|
"Throttle" help by benha » Wed, 2019-08-07 05:58 |
0 |
by benha Wed, 2019-08-07 05:58 |
|
|
Need help maximizing torque at low RPM - FOC, Hub motors, Flipsky VESC 4.12 50A by Bruce » Mon, 2021-03-15 03:31 |
0 |
by Bruce Mon, 2021-03-15 03:31 |
Log in to post new content in the forum.
