You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Control type = Current No Reverse With Brake by perpetum » Mon, 2020-11-02 05:00 |
0 |
by perpetum Mon, 2020-11-02 05:00 |
|
|
Dutycyle dropping under load by Julzz112 » Sun, 2024-04-14 18:31 |
0 |
by Julzz112 Tue, 2024-04-16 08:26 |
|
|
FSESC 75100 motor problem by anythingstl » Tue, 2024-02-13 17:15 |
0 |
by anythingstl Mon, 2024-02-19 19:23 |
|
|
help needed with raptor 2 remote by dave9401 » Mon, 2020-11-02 10:26 |
0 |
by dave9401 Mon, 2020-11-02 10:26 |
|
|
Dual motor setup for Turnigy SK8 V2 60A x 2 3~12S Twin Motor Skateboard ESC? by fil02184 » Tue, 2022-10-18 04:07 |
0 |
by fil02184 Tue, 2022-10-18 16:00 |
|
|
Using Motor hall sensors as the encoder by Russ g » Wed, 2019-05-08 16:01 |
0 |
by Russ g Wed, 2019-05-08 16:01 |
|
|
DRV8323 by Jessica » Thu, 2019-03-14 11:41 |
0 |
by Jessica Thu, 2019-03-14 11:42 |
|
|
Flipsky VESC 4.20 with 5.1 Firmware PWM input offset by mantisrobot » Thu, 2020-11-05 12:24 |
0 |
by mantisrobot Thu, 2020-11-05 12:24 |
|
|
Noob here by Nothanks » Sat, 2024-04-20 01:21 |
0 |
by Nothanks Sat, 2024-04-20 01:21 |
|
|
20S by ahanktcd » Thu, 2024-04-25 14:51 |
0 |
by ahanktcd Thu, 2024-04-25 14:51 |
|
|
FAULT_CODE_DRV by Yuna » Tue, 2024-02-27 12:08 |
0 |
by Yuna Tue, 2024-02-27 12:08 |
|
|
G60 motor hall wires pinout by Talonkid119 » Wed, 2024-03-06 03:43 |
0 |
by Talonkid119 Wed, 2024-03-06 03:43 |
|
|
STM32F407 by john » Wed, 2019-03-27 13:40 |
0 |
by john Wed, 2019-03-27 13:40 |
|
|
optimizing ebike - vesc 75300 by stealth13 » Fri, 2024-05-03 01:28 |
0 |
by stealth13 Fri, 2024-05-03 01:28 |
|
|
Porting VESC to STML4 by Vince_1618 » Fri, 2022-10-28 14:01 |
0 |
by Vince_1618 Fri, 2022-10-28 14:01 |
|
|
HFI optimisation with increase in switching frequency by rainebk@bigpond... » Tue, 2022-09-13 06:53 |
0 |
by rainebk@bigpond... Tue, 2022-09-13 06:53 |
|
|
VESC Wand shows INF and 100% Batt by BLKFLD » Sat, 2020-09-26 04:48 |
0 |
by BLKFLD Sat, 2020-09-26 04:48 |
|
|
Setting the motor parameters by Lenar » Sat, 2024-05-04 10:18 |
0 |
by Lenar Sat, 2024-05-04 10:18 |
|
|
Tuning process? by wingborne » Tue, 2020-09-29 00:09 |
0 |
by wingborne Tue, 2020-09-29 21:39 |
|
|
Battery percentage mapping by Sharkboy » Mon, 2024-05-06 22:55 |
0 |
by Sharkboy Mon, 2024-05-06 22:55 |
|
|
Runtime motor control with CAN by Davidepolpi91 » Fri, 2024-03-15 15:12 |
0 |
by Davidepolpi91 Fri, 2024-03-15 15:12 |
|
|
Battlebot Weapon : Trouble spinning up by satacoy » Thu, 2019-04-04 07:29 |
0 |
by satacoy Thu, 2019-04-04 07:29 |
|
|
Speed control issues w. hub motors by akerblad » Sun, 2019-04-07 17:22 |
0 |
by akerblad Sun, 2019-04-07 17:22 |
|
|
Implementing developer tools and PID tuning by nowholeself » Wed, 2020-10-07 07:04 |
0 |
by nowholeself Wed, 2020-10-07 07:04 |
|
|
Flysky FESC 6.7 to disable 5V by AryehChen » Wed, 2024-05-15 18:44 |
0 |
by AryehChen Wed, 2024-05-15 18:46 |
Log in to post new content in the forum.
