You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
How to set up RF receiver for PPM or UART input? by adamdorr » Tue, 2020-01-07 16:23 |
0 |
by adamdorr Tue, 2020-01-07 16:23 |
|
Vesc WS2812b led issues & support by Ash » Tue, 2019-11-12 08:40 |
0 |
by Ash Tue, 2019-11-12 14:13 |
|
Can bus communication. by Piamen » Wed, 2019-11-27 06:47 |
0 |
by Piamen Wed, 2019-11-27 06:47 |
|
Unofficial VESC Discord server by kubark42 » Tue, 2021-11-16 16:07 |
0 |
by kubark42 Fri, 2021-11-19 03:12 |
|
DRV8302 Gate Pin output waveform is abnormal by yandongyu1998 » Fri, 2019-12-13 07:21 |
0 |
by yandongyu1998 Fri, 2019-12-13 07:21 |
|
The rpm control is not working properly by ptss37 » Wed, 2021-11-24 03:30 |
0 |
by ptss37 Wed, 2021-11-24 03:44 |
|
Any issues with the DRV8323? by shaman » Thu, 2019-10-24 21:50 |
0 |
by shaman Thu, 2019-10-24 21:50 |
|
BRAND NEW R SPEC DUAL 6355 (4.12 VESC) SET UP ISSUES by rodriguezjoe1@b... » Mon, 2020-09-07 17:50 |
0 |
by rodriguezjoe1@b... Mon, 2020-09-07 17:50 |
|
Making master and slave motors communicate both ways by Sis7 » Tue, 2020-07-21 05:58 |
0 |
by Sis7 Tue, 2020-07-21 05:58 |
|
Best way to run a hoverboard motor that has an AB encoder and Hall sensors, but no index? by PaulMakesThings » Thu, 2022-06-23 23:43 |
0 |
by PaulMakesThings Thu, 2022-06-23 23:43 |
|
GT2 Remote to Vesc connection issue by tom.embke » Tue, 2018-05-01 14:41 |
0 |
by tom.embke Tue, 2018-05-01 14:41 |
|
resistance and inductance value changes when each measurement by alexshen2012 » Fri, 2022-07-01 05:42 |
0 |
by alexshen2012 Fri, 2022-07-01 05:42 |
|
can not start motor with high duty by qdxiatao » Sat, 2018-03-24 03:58 |
0 |
by qdxiatao Sat, 2018-03-24 03:58 |
|
encoder detection error by qdxiatao » Wed, 2018-05-09 12:04 |
0 |
by qdxiatao Wed, 2018-05-09 12:04 |
|
VESC custom firmware custom UART message by steveyplst » Tue, 2020-08-04 10:23 |
0 |
by steveyplst Tue, 2020-08-04 10:23 |
|
VESC specialist required. by BlackPanthera » Mon, 2022-07-18 17:11 |
0 |
by BlackPanthera Mon, 2022-07-18 17:11 |
|
connecting vesc tool with Prototipo by Govert » Thu, 2020-07-02 19:43 |
0 |
by Govert Thu, 2020-07-02 19:43 |
|
How do you turn on traction control ( I can't remember) by msim2 » Fri, 2022-05-20 22:06 |
0 |
by msim2 Fri, 2022-05-20 22:06 |
|
VESC 6 Mark III and Traxxas Summit Radio Receiver PWM / PPM Signals by j98221@gmail.com » Fri, 2020-07-03 07:27 |
0 |
by j98221@gmail.com Fri, 2020-07-03 07:27 |
|
My VESC TOOL did not have "balance" by Elijah K » Wed, 2020-08-12 07:52 |
0 |
by Elijah K Wed, 2020-08-12 07:53 |
|
ADC input protection proposal by arestechfinland » Mon, 2020-07-06 19:41 |
0 |
by arestechfinland Mon, 2020-07-06 19:41 |
|
VESC with asynchronous motors by afbbfa » Fri, 2022-07-29 22:51 |
0 |
by afbbfa Fri, 2022-07-29 22:51 |
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse » Fri, 2022-06-03 08:13 |
0 |
by notahorse Fri, 2022-06-03 08:13 |
|
Regenerative braking in scooter Zero x11 72V dual motor 2 x 1600 w peak power 6000W by Makroman » Wed, 2020-07-08 20:00 |
0 |
by Makroman Wed, 2020-07-08 20:00 |
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 » Mon, 2022-08-01 18:08 |
0 |
by moose09876 Mon, 2022-08-01 18:08 |
Log in to post new content in the forum.