You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC 6 EDU: Motor Wizard - Detection failed by Navigator_PJE » Mon, 2022-08-29 16:12 |
0 |
by Navigator_PJE Mon, 2022-08-29 16:12 |
|
|
Flipsky Mini FSESC 6.7 Pro Red LED flashes every two seconds by never » Sun, 2023-12-17 08:59 |
0 |
by never Sun, 2023-12-17 08:59 |
|
|
Is this current reading normal? by AliBarrett10 » Sat, 2021-07-17 12:59 |
0 |
by AliBarrett10 Sat, 2021-07-17 12:59 |
|
|
GT2 Remote to Vesc connection issue by tom.embke » Tue, 2018-05-01 14:41 |
0 |
by tom.embke Tue, 2018-05-01 14:41 |
|
|
Flipsky Mini FSESC 6.7 Pro Red LED flashes every two seconds by never » Sun, 2023-12-17 09:03 |
0 |
by never Sun, 2023-12-17 09:03 |
|
|
Angle offset detection by Gas_Sn4ke » Mon, 2019-01-21 07:09 |
0 |
by Gas_Sn4ke Mon, 2019-01-21 07:09 |
|
|
can not start motor with high duty by qdxiatao » Sat, 2018-03-24 03:58 |
0 |
by qdxiatao Sat, 2018-03-24 03:58 |
|
|
FOC parameters keep disappearing by Gsorter » Thu, 2023-08-24 22:20 |
0 |
by Gsorter Fri, 2023-08-25 16:26 |
|
|
Separate Deadband for ADC2? by striderkent » Wed, 2019-01-23 16:31 |
0 |
by striderkent Wed, 2019-01-23 16:31 |
|
|
PID_POS_NOW by Persius48 » Tue, 2023-09-12 19:14 |
0 |
by Persius48 Tue, 2023-09-12 19:14 |
|
|
FOC HFI Voltage by lennyhaacker » Tue, 2021-07-27 04:24 |
0 |
by lennyhaacker Tue, 2021-07-27 04:24 |
|
|
Rickshaw Motor - Typical 48V 1000W motors available by sweendog311 » Wed, 2023-09-20 22:52 |
0 |
by sweendog311 Wed, 2023-09-20 22:52 |
|
|
Does unbalanced resistance/inductance still cause issues with FOC HFI? by SeventhSeeker » Tue, 2021-08-10 13:47 |
0 |
by SeventhSeeker Tue, 2021-08-10 13:47 |
|
|
Problem with encoder readings with arduino by ruthvikchanda » Thu, 2018-12-06 07:06 |
0 |
by ruthvikchanda Thu, 2018-12-06 10:23 |
|
|
VESC BMS Charger Disengaging early by sandersesurf » Tue, 2024-01-09 13:56 |
0 |
by sandersesurf Tue, 2024-01-09 13:56 |
|
|
Connect multiple VESCs together and communicate over CAN by mustard666 » Fri, 2023-10-06 23:32 |
0 |
by mustard666 Fri, 2023-10-06 23:32 |
|
|
flipsky 6374 battle hardened with flipsky 6.6 dual vesc by marso » Sun, 2021-08-22 17:35 |
0 |
by marso Sun, 2021-08-22 17:36 |
|
|
VESC 75/250 Schematic Diagram by georgeli293 » Thu, 2024-01-18 19:13 |
0 |
by georgeli293 Thu, 2024-01-18 19:13 |
|
|
BATTERY_VOLTAGE_HIGH_CUTOFF_START // CUTOFF_END ? by Andy G » Mon, 2023-10-16 18:41 |
0 |
by Andy G Mon, 2023-10-16 18:43 |
|
|
dual vesc question by badger1666 » Sun, 2018-10-28 12:59 |
0 |
by badger1666 Sun, 2018-10-28 12:59 |
|
|
Spin motor at constant ERPM while a button is pressed by t-dub-maui » Fri, 2024-01-26 07:33 |
0 |
by t-dub-maui Fri, 2024-01-26 07:33 |
|
|
Slow ABS current limit. by Faheem » Tue, 2023-10-24 07:49 |
0 |
by Faheem Tue, 2023-10-24 07:49 |
|
|
Battery current limit problems by ziumus » Mon, 2021-08-30 21:37 |
0 |
by ziumus Mon, 2021-08-30 21:37 |
|
|
How to control two Can-connected motors separately from microcontroller. by kkkeisuke » Sun, 2021-06-20 06:47 |
0 |
by kkkeisuke Sun, 2021-06-20 12:05 |
|
|
Cruise function already implemented? by sam.vanratt » Wed, 2019-01-02 17:05 |
0 |
by sam.vanratt Wed, 2019-01-02 17:20 |
Log in to post new content in the forum.
