You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
vesc6 help with hub motor by badger1666 » Thu, 2018-12-20 18:36 |
4 |
by badger1666 Fri, 2018-12-21 06:03 |
|
|
Differential steering setup by GCTech » Sat, 2020-07-04 17:38 |
4 |
by CalLangford Fri, 2024-09-20 20:29 |
|
|
Rolling down-hill faster than my board's electric top speed by koralle » Tue, 2018-05-01 21:18 |
4 |
by koralle Sun, 2018-05-06 18:25 |
|
|
VESC 6 hi voltage problem by mike » Fri, 2018-05-04 11:34 |
4 |
by mike Tue, 2018-05-08 19:31 |
|
|
ADC1 problems with Firmware/Hardware issue? by sam.vanratt » Thu, 2018-12-27 22:31 |
4 |
by sam.vanratt Thu, 2019-01-03 17:46 |
|
|
Too little torque. by Roger Wolff » Thu, 2018-05-10 18:11 |
4 |
by Roger Wolff Mon, 2018-05-14 19:30 |
|
|
Roll-to-start VESC by dsuresh » Fri, 2021-03-12 21:05 |
4 |
by robertkovax Fri, 2023-11-10 16:57 |
|
|
e-bike hubmotor problem by Ratereducer » Fri, 2023-07-14 23:35 |
4 |
by Ratereducer Thu, 2023-09-07 23:31 |
|
|
Very Large hub motor detection (QSMOTOR 3000W hub) by shaman » Thu, 2020-02-20 01:26 |
5 |
by fart Wed, 2024-04-03 10:43 |
|
|
HFI and a big in-runner? 65121 Motor and Flipsky 75200 Pro V2 ESC. by ajtalbot1 » Thu, 2024-08-22 20:18 |
5 |
by ajtalbot1 Tue, 2024-08-27 20:27 |
|
|
PID Position Controller by IanG » Wed, 2020-03-25 03:05 |
5 |
by Luke264 Wed, 2021-02-17 18:53 |
|
|
Reading tachometer over can bus by kimpet » Sun, 2019-05-12 22:24 |
5 |
by benjamin Sun, 2019-05-19 14:58 |
|
|
VESC as a 3 phase inverter to power a grid model by pf26 » Tue, 2019-03-19 20:54 |
5 |
by shaman Fri, 2019-10-18 15:06 |
|
|
un-commanded reverse pulse by maxhurtz » Fri, 2022-09-02 16:01 |
5 |
by canoeman Thu, 2022-09-15 19:21 |
|
|
SK3 Turnigy 6374 149 / encoder CUI AMT102 => can VESC 4 support position control? by fourchette » Tue, 2019-04-02 23:14 |
5 |
by pf26 Thu, 2019-04-04 11:43 |
|
|
3 sensorless motors connected with belt by moose09876 » Wed, 2022-09-14 23:26 |
5 |
by moose09876 Fri, 2022-09-16 14:09 |
|
|
Arduino UART max Current and max RPM setting by h2omatt » Wed, 2020-09-30 23:49 |
5 |
by dsuresh Tue, 2021-06-08 20:59 |
|
|
what is the best vesc For long-term sea observation by jhgjg » Thu, 2022-09-22 12:12 |
5 |
by frank Mon, 2022-09-26 15:44 |
|
|
VESC 75/300, TP 100 inrunner 10KW by Markula » Thu, 2019-05-02 13:58 |
5 |
by Markula Wed, 2019-05-08 18:59 |
|
|
AMT 102 Encoder not working properly with VESC by DerpRush » Thu, 2019-07-25 11:32 |
5 |
by ripperpc Wed, 2022-04-06 21:36 |
|
|
Problem to start bldc in vesc tool vesc-mini4 esc by uav-orion » Wed, 2019-06-12 16:18 |
5 |
by uav-orion Wed, 2019-06-19 21:50 |
|
|
PWM on output by ml2311 » Tue, 2021-08-24 14:46 |
5 |
by Flyingtux Wed, 2022-03-30 19:31 |
|
|
vesc throttle response by TONY61 » Tue, 2025-02-04 16:20 |
5 |
by Groundspeed100 Mon, 2025-03-10 20:23 |
|
|
trampa by badger1666 » Mon, 2017-12-11 22:37 |
5 |
by wdaehn Wed, 2017-12-13 12:17 |
|
|
Sudden kick (from motor current cut off?) by darowi » Mon, 2017-10-02 18:56 |
5 |
by darowi Tue, 2020-09-15 12:45 |
Log in to post new content in the forum.
