You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Slow ABS current limit. by Faheem » Tue, 2023-10-24 07:49 |
0 |
by Faheem Tue, 2023-10-24 07:49 |
|
|
Battery current limit problems by ziumus » Mon, 2021-08-30 21:37 |
0 |
by ziumus Mon, 2021-08-30 21:37 |
|
|
How to control two Can-connected motors separately from microcontroller. by kkkeisuke » Sun, 2021-06-20 06:47 |
0 |
by kkkeisuke Sun, 2021-06-20 12:05 |
|
|
Brake Button Gradual Braking by hackish » Thu, 2019-09-05 16:56 |
0 |
by hackish Thu, 2019-09-05 16:56 |
|
|
boost mode for 15sec by mantashook@gmail.com » Sat, 2023-11-04 23:00 |
0 |
by mantashook@gmail.com Sat, 2023-11-04 23:00 |
|
|
Connecting reverse button to Trampa vesc by Oded Mazor » Fri, 2023-07-28 08:09 |
0 |
by Oded Mazor Fri, 2023-07-28 08:11 |
|
|
Flipsky broken off USB ports by mnchvgs79 » Fri, 2021-06-25 20:25 |
0 |
by mnchvgs79 Fri, 2021-06-25 20:25 |
|
|
reverse programing by axialflux » Mon, 2023-11-13 23:21 |
0 |
by axialflux Mon, 2023-11-13 23:21 |
|
|
Issue with my Blacktip program by salmanbinm » Mon, 2023-07-31 21:00 |
0 |
by salmanbinm Mon, 2023-07-31 21:00 |
|
|
PAS and Throttle by nguyen victor » Tue, 2021-06-29 14:55 |
0 |
by nguyen victor Tue, 2021-06-29 14:55 |
|
|
Remote pairs but motor does not spin after VESC tool use by frunobulax » Fri, 2025-04-11 18:26 |
0 |
by frunobulax Fri, 2025-04-11 18:26 |
|
|
Flipsky 75100 + tft screen by omrishalev123 » Mon, 2024-12-30 23:10 |
0 |
by omrishalev123 Mon, 2024-12-30 23:10 |
|
|
Voltage on motor leads @ 0 throttle by SimpleUnmanned » Thu, 2020-05-21 02:40 |
0 |
by SimpleUnmanned Thu, 2020-05-21 02:40 |
|
|
Is BMS Tool compatible with LTO batteries? by SteveBrantley » Fri, 2025-04-18 23:12 |
0 |
by SteveBrantley Fri, 2025-04-18 23:12 |
|
|
75100 recognized as 75300 and nothing works by anaka » Mon, 2025-01-20 19:59 |
0 |
by anaka Mon, 2025-01-20 19:59 |
|
|
What is the current state of mcus support? by il_piccione » Fri, 2025-04-25 09:47 |
0 |
by il_piccione Fri, 2025-04-25 09:47 |
|
|
PPM+UART. RC and esp32 by coldreboot » Thu, 2025-01-30 23:20 |
0 |
by coldreboot Fri, 2025-01-31 15:50 |
|
|
Adjusting Acceleration Ramp with NRF & Current control by Mido » Tue, 2022-04-05 14:36 |
0 |
by Mido Tue, 2022-04-05 14:36 |
|
|
How to set dead time on BLDC mode? by AllenFF » Wed, 2020-04-15 03:30 |
0 |
by AllenFF Mon, 2020-04-27 15:34 |
|
|
Flipsky 75200 Motor ruckelt und wird sehr schnell heiß by Oriessin » Sat, 2025-04-26 07:38 |
0 |
by Oriessin Sat, 2025-04-26 07:38 |
|
|
Best Throttle and break level by ardillolambo » Wed, 2022-03-02 18:29 |
0 |
by ardillolambo Wed, 2022-03-02 18:29 |
|
|
Measurement of voltage and mah by renaudbarbier » Sun, 2020-05-31 17:04 |
0 |
by renaudbarbier Sun, 2020-05-31 17:04 |
|
|
Vesc firmware to programmable Sabvoton ml60 controller. by Maciejwarloch » Tue, 2022-03-08 14:19 |
0 |
by Maciejwarloch Tue, 2022-03-08 14:19 |
|
|
VESC Connect dongle alternatives by Pimousse » Tue, 2020-06-02 15:32 |
0 |
by Pimousse Tue, 2020-06-02 15:32 |
|
|
Battery charging using motor inductance by eptv » Sun, 2020-04-26 07:44 |
0 |
by eptv Sun, 2020-04-26 07:44 |
Log in to post new content in the forum.
