You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Sub zero temperature VESC412 issues by jetigm » Fri, 2019-02-08 21:12 |
3 |
by sam.vanratt Sun, 2019-02-10 14:07 |
|
|
Sudden drop in speed after releasing throttle in FW mode by shokrabi » Sat, 2022-04-23 15:05 |
4 |
by DeuceDos Tue, 2023-05-30 09:54 |
|
|
Sudden hard acceleration at around 30 km/h. Help by kristofferbenjaminw » Tue, 2022-10-04 17:31 |
4 |
by Chris Barth Tue, 2022-10-11 20:05 |
|
|
Sudden kick (from motor current cut off?) by darowi » Mon, 2017-10-02 18:56 |
5 |
by darowi Tue, 2020-09-15 12:45 |
|
|
Sudden motor stop by dmcke5 » Wed, 2018-08-15 13:50 |
2 |
by andreas Thu, 2018-09-06 20:48 |
|
|
Suddenly broken by moto_guy » Fri, 2019-03-08 13:50 |
10 |
by David_1 Fri, 2022-06-17 21:07 |
|
|
Suggestion for new forum area by Snabelost » Thu, 2022-10-06 23:55 |
2 |
by Snabelost Tue, 2022-10-11 18:30 |
|
|
swagatron hoverboard motors with VESC by popeye243 » Tue, 2020-07-21 02:49 |
13 |
by popeye243 Mon, 2020-09-07 03:42 |
|
|
swap PWM H and PWM L Pins on STM32F4 by Urs_Harry » Tue, 2022-03-15 23:04 |
3 |
by skyline1970 Thu, 2022-03-17 09:58 |
|
|
Switch between pre-defined profiles over UART by PutridFox » Sun, 2025-06-15 13:11 |
0 |
by PutridFox Sun, 2025-06-15 13:11 |
|
|
Switch two Motor Profiles/Modes (UART) by anli » Thu, 2018-08-16 19:02 |
7 |
by basti30 Sun, 2018-09-30 19:55 |
|
|
Switching between hall and observer by eptv » Thu, 2019-12-05 08:49 |
1 |
by frank Thu, 2019-12-05 10:54 |
|
|
Switching control scheme during opertion by Ben Murton » Tue, 2023-01-31 02:57 |
1 |
by Gos1 Mon, 2023-06-26 12:07 |
|
|
Switching frequency factor 2 lower by Elwin » Sat, 2021-11-13 22:48 |
10 |
by Elwin Sun, 2022-01-09 08:31 |
|
|
switching power supply by MagicKey » Tue, 2023-01-17 04:01 |
2 |
by vadicus Fri, 2023-06-23 22:59 |
|
|
Sync loss when switching from HALL to sensorless by blezalex » Fri, 2019-05-24 19:00 |
1 |
by blezalex Mon, 2019-06-10 23:26 |
|
|
Synchronizing multiple motors before mechanically locking together by hockinsk » Sun, 2019-10-27 23:15 |
2 |
by Stupidspencer Sun, 2019-12-15 22:50 |
|
|
Tach output changes when switching from BLDC --> FOC by Zoxks » Sun, 2024-12-01 20:28 |
1 |
by Zoxks Tue, 2024-12-03 19:10 |
|
|
Tachometer VS RPM by Davideo » Mon, 2018-02-05 03:17 |
2 |
by Davideo Tue, 2018-02-06 00:37 |
|
|
Tell me how to accurately determine the type of engine FOC, BLDC by Valera1996 » Sun, 2020-02-09 18:53 |
8 |
by vadicus Mon, 2020-02-17 22:41 |
|
|
temperature compensation make sense？ by alexshen2012 » Thu, 2022-08-04 08:28 |
1 |
by alexshen2012 Thu, 2022-08-04 09:17 |
|
|
The controller is not responding by TheJuan901 » Sat, 2026-03-14 02:03 |
0 |
by TheJuan901 Sat, 2026-03-14 02:03 |
|
|
the keyboard control doesn't work by dmarko16 » Sun, 2021-02-07 15:34 |
1 |
by skyline1970 Sun, 2021-02-07 17:13 |
|
|
The motor with an enkoder of AS5048 rotates unevenly by densor » Thu, 2018-04-26 11:41 |
2 |
by densor Fri, 2018-04-27 08:27 |
|
|
The rpm control is not working properly by ptss37 » Wed, 2021-11-24 03:30 |
0 |
by ptss37 Wed, 2021-11-24 03:44 |
Log in to post new content in the forum.
