You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Control type = Current No Reverse With Brake by perpetum » Mon, 2020-11-02 05:00 |
0 |
by perpetum Mon, 2020-11-02 05:00 |
|
|
help needed with raptor 2 remote by dave9401 » Mon, 2020-11-02 10:26 |
0 |
by dave9401 Mon, 2020-11-02 10:26 |
|
|
Position Control with Resolver by robo_studienarbeit » Tue, 2018-10-16 18:57 |
0 |
by robo_studienarbeit Tue, 2018-10-16 18:57 |
|
|
Flipsky VESC 4.20 with 5.1 Firmware PWM input offset by mantisrobot » Thu, 2020-11-05 12:24 |
0 |
by mantisrobot Thu, 2020-11-05 12:24 |
|
|
resistance and inductance value changes when each measurement by alexshen2012 » Fri, 2022-07-01 05:42 |
0 |
by alexshen2012 Fri, 2022-07-01 05:42 |
|
|
Simulating controller accurately by TechAUmNu » Fri, 2019-08-16 15:35 |
0 |
by TechAUmNu Fri, 2019-08-16 15:35 |
|
|
foc with encoder fails to run smoothly by jdn » Thu, 2019-08-22 12:26 |
0 |
by jdn Thu, 2019-08-22 15:47 |
|
|
VESC specialist required. by BlackPanthera » Mon, 2022-07-18 17:11 |
0 |
by BlackPanthera Mon, 2022-07-18 17:11 |
|
|
How do you turn on traction control ( I can't remember) by msim2 » Fri, 2022-05-20 22:06 |
0 |
by msim2 Fri, 2022-05-20 22:06 |
|
|
How to Write Serial Communication Program Not Applicable to RTOS by Jack_Li » Fri, 2019-07-05 06:55 |
0 |
by Jack_Li Fri, 2019-07-05 06:58 |
|
|
Reverse and brake inputs? by hackish » Sat, 2019-09-07 19:20 |
0 |
by hackish Sat, 2019-09-07 19:20 |
|
|
VESC to test e-Bike motor and car alternator as Torque Load..? by arifbustani » Thu, 2019-09-12 19:00 |
0 |
by arifbustani Thu, 2019-09-12 19:00 |
|
|
VESC with asynchronous motors by afbbfa » Fri, 2022-07-29 22:51 |
0 |
by afbbfa Fri, 2022-07-29 22:51 |
|
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse » Fri, 2022-06-03 08:13 |
0 |
by notahorse Fri, 2022-06-03 08:13 |
|
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 » Mon, 2022-08-01 18:08 |
0 |
by moose09876 Mon, 2022-08-01 18:08 |
|
|
Current loop resonance in higher ERPM under Current Mode by ypl » Sat, 2019-07-20 09:34 |
0 |
by ypl Sat, 2019-07-20 09:34 |
|
|
VESC as generator - settings confirmation by justinlsquire » Mon, 2022-06-06 02:44 |
0 |
by justinlsquire Mon, 2022-06-06 02:44 |
|
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset » Thu, 2022-08-04 01:44 |
0 |
by liminalsunset Thu, 2022-08-04 01:44 |
|
|
VESC with no working brake button by tavsanist » Sat, 2019-07-27 02:40 |
0 |
by tavsanist Sat, 2019-07-27 02:40 |
|
|
Because..why not: Full Self Riding Skateboard (autonomous skateboard) by x78163 » Wed, 2022-06-08 17:33 |
0 |
by x78163 Wed, 2022-06-08 17:33 |
|
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings » Fri, 2022-08-05 11:06 |
0 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
|
|
"Throttle" help by benha » Wed, 2019-08-07 05:58 |
0 |
by benha Wed, 2019-08-07 05:58 |
|
|
Best way to run a hoverboard motor that has an AB encoder and Hall sensors, but no index? by PaulMakesThings » Thu, 2022-06-23 23:43 |
0 |
by PaulMakesThings Thu, 2022-06-23 23:43 |
|
|
Query: Can I run my 70-pole motor using a VESC-based Flipskey controller? by avaid » Thu, 2025-05-08 12:57 |
0 |
by avaid Tue, 2025-05-13 08:02 |
|
|
Drive frequency and command rate question by jediengineer » Sun, 2023-03-19 19:07 |
0 |
by jediengineer Sun, 2023-03-19 19:08 |
Log in to post new content in the forum.
