You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Throttle curves by Phill Dixon » Wed, 2018-05-23 18:16 |
1 |
by Tilman Baumann Thu, 2018-05-24 11:33 |
|
|
VESC "underpowered" vs Kunteng Controller experience by andyw2005 » Thu, 2021-10-21 23:54 |
1 |
by Elwin Fri, 2021-10-22 11:39 |
|
|
Lispscript help by mrendu43 » Mon, 2024-04-01 09:57 |
1 |
by woozie Mon, 2024-09-23 22:53 |
|
|
Working on Open Source Remote Control for Differential Drive Robot using BLE by ilektron » Tue, 2021-11-30 03:02 |
1 |
by x78163 Wed, 2022-06-08 17:07 |
|
|
Vesc 6 MKIV Power Switch by KitemillAS » Wed, 2021-12-01 19:44 |
1 |
by frank Wed, 2021-12-01 22:04 |
|
|
Looking to Hire by TeleTour » Tue, 2021-10-26 07:34 |
1 |
by skyline1970 Wed, 2021-10-27 11:54 |
|
|
Compiling in a different config. by Roger Wolff » Mon, 2018-09-17 17:07 |
1 |
by TechAUmNu Mon, 2018-09-17 17:12 |
|
|
VESC Error "No firmware response" by Magoroth » Tue, 2018-06-12 15:41 |
1 |
by hexakopter Wed, 2018-06-13 01:12 |
|
|
Raptor 2 by Phill Dixon » Wed, 2018-06-13 18:07 |
1 |
by frank Fri, 2018-06-22 11:35 |
|
|
20x4.0 fat bike with Bafang geared hub motor (low torque) by Ro » Tue, 2024-04-16 10:30 |
1 |
by Buddy Love Sat, 2024-08-10 19:07 |
|
|
VESC Hardware link broken by jparadie » Mon, 2018-06-18 12:21 |
1 |
by frank Fri, 2018-06-22 11:33 |
|
|
3v3 Regulator fried? How to check if STM was affected too? by Seudo » Fri, 2024-02-16 19:48 |
1 |
by bww129 Fri, 2024-03-15 05:36 |
|
|
VESC 100/250 by PBR-Automatyka » Tue, 2021-11-02 12:17 |
1 |
by PBR-Automatyka Tue, 2021-11-02 12:18 |
|
|
tuning PID speed for the skateboard motor with hall sensors by salviador » Tue, 2021-09-14 14:37 |
1 |
by skyline1970 Sat, 2021-09-18 11:18 |
|
|
MTPA by hummina » Tue, 2024-02-20 19:54 |
1 |
by Rohan_Suresh_babu Mon, 2024-03-04 06:21 |
|
|
MakerX-FOC DV6s PWM for 2 BLDC Motors by paulsimpsonii » Tue, 2026-03-03 18:08 |
0 |
by paulsimpsonii Tue, 2026-03-03 18:08 |
|
|
VESC custom firmware custom UART message by steveyplst » Tue, 2020-08-04 10:23 |
0 |
by steveyplst Tue, 2020-08-04 10:23 |
|
|
The controller is not responding by TheJuan901 » Sat, 2026-03-14 02:03 |
0 |
by TheJuan901 Sat, 2026-03-14 02:03 |
|
|
Flipsky FSV 6.6 no longer working with new VESC Tool by oliver1998 » Fri, 2025-09-12 06:06 |
0 |
by oliver1998 Fri, 2025-09-12 06:06 |
|
|
Dultron X2 UP by timgunn5555 » Wed, 2026-03-18 02:34 |
0 |
by timgunn5555 Wed, 2026-03-18 02:34 |
|
|
Dual VESC Controller - Internal CAN Forwarding Failure -NOW WITH CODE EXAMPLE ;) by XAQ » Mon, 2025-09-15 07:52 |
0 |
by XAQ Mon, 2025-09-15 17:42 |
|
|
2 Speed ADC control by totalgeek9224 » Mon, 2025-09-22 19:47 |
0 |
by totalgeek9224 Mon, 2025-09-22 19:47 |
|
|
Step/Dir signals by wall0069 » Sun, 2019-06-09 16:06 |
0 |
by wall0069 Sun, 2019-06-09 16:06 |
|
|
VESC specialist required. by BlackPanthera » Mon, 2022-07-18 17:11 |
0 |
by BlackPanthera Mon, 2022-07-18 17:11 |
|
|
connecting vesc tool with Prototipo by Govert » Thu, 2020-07-02 19:43 |
0 |
by Govert Thu, 2020-07-02 19:43 |
Log in to post new content in the forum.
