You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Flipsky 75/100 Mosfet short? by Michael Campbell » Mon, 2022-04-11 08:29 |
4 |
by Michael Campbell Tue, 2022-04-12 00:03 |
|
|
Motor compatibility (and power levels) by MrSurly » Tue, 2022-04-12 21:43 |
0 |
by MrSurly Tue, 2022-04-12 21:43 |
|
|
Flux linkage detection failed by Count1310 » Sat, 2020-08-22 16:30 |
3 |
by drummerboy5408 Wed, 2022-04-13 07:42 |
|
|
Hybrid mode in FOC - possible? by Oded Mazor » Tue, 2022-04-12 07:42 |
4 |
by Oded Mazor Wed, 2022-04-13 11:28 |
|
|
Your input needed: FESC 4.12 / Arduino / 4X 350W motors by matukash » Tue, 2020-07-21 16:36 |
6 |
by frank Fri, 2022-04-15 17:31 |
|
|
Control of 4000w bldc motor with hall effect sensors by Abdullah Ajmal » Sat, 2022-04-16 10:14 |
1 |
by frank Sat, 2022-04-16 20:01 |
|
|
Servo output CAN Formats by vinci » Mon, 2022-04-18 15:35 |
0 |
by vinci Mon, 2022-04-18 15:35 |
|
|
Design custom VESC 6 Hardware by brightlightbeam » Sat, 2020-07-04 14:18 |
5 |
by Gatze Mon, 2022-04-18 18:22 |
|
|
Where can I ask technical questions about products? by MrSurly » Tue, 2022-04-19 05:22 |
0 |
by MrSurly Tue, 2022-04-19 05:22 |
|
|
Motor detection failed by DragosZapodeanu » Tue, 2022-04-19 15:09 |
0 |
by DragosZapodeanu Tue, 2022-04-19 15:09 |
|
|
Autonomous Drifting Research Project by AutonomousDrifting » Fri, 2020-10-30 13:05 |
1 |
by AutonomousDrifting Tue, 2022-04-19 23:21 |
|
|
Vesc is not turning on by asnamp » Wed, 2022-04-20 09:30 |
1 |
by canoeman Wed, 2022-04-20 15:44 |
|
|
Multiple VESCs on the same battery by Riccio » Wed, 2022-04-20 22:09 |
0 |
by Riccio Wed, 2022-04-20 22:09 |
|
|
VESC is not working in ADC mode by asnamp » Wed, 2022-04-20 09:21 |
0 |
by asnamp Thu, 2022-04-21 20:11 |
|
|
VESC is not working in ADC mode by asnamp » Thu, 2022-04-21 06:53 |
2 |
by asnamp Fri, 2022-04-22 06:50 |
|
|
Bluetooth module in VESC 75/300 by Hermann Schnaeuzle » Fri, 2022-04-22 17:55 |
0 |
by Hermann Schnaeuzle Fri, 2022-04-22 17:55 |
|
|
Brake hiccup by Phill Dixon » Wed, 2022-03-30 18:23 |
23 |
by Phill Dixon Mon, 2022-04-25 17:45 |
|
|
Wand (and app) not pairing by Jonny254 » Mon, 2019-10-07 15:17 |
3 |
by Daada Wed, 2022-04-27 10:58 |
|
|
Control singular VESC using CAN-BUS and Arduino by Cam » Wed, 2021-01-06 10:29 |
4 |
by craiggault Wed, 2022-04-27 23:07 |
|
|
Firmware by Phill Dixon » Mon, 2022-04-25 15:29 |
7 |
by frank Sat, 2022-04-30 14:21 |
|
|
VESC 100/250: analog regen brake AND e-brake cut switch? by fatty » Thu, 2021-05-13 01:16 |
2 |
by frank Mon, 2022-05-02 09:11 |
|
|
Previous tool+5.2 by Phill Dixon » Sun, 2022-05-01 07:50 |
1 |
by frank Mon, 2022-05-02 09:12 |
|
|
VESC output current decreasing in time by isso777 » Sat, 2022-04-30 14:59 |
5 |
by isso777 Mon, 2022-05-02 17:30 |
|
|
Insufficient torque at low RPM by isso777 » Sat, 2022-04-23 21:13 |
10 |
by frank Tue, 2022-05-03 08:18 |
|
|
CAN Analyzer by min » Tue, 2022-05-03 10:38 |
0 |
by min Tue, 2022-05-03 10:38 |
Log in to post new content in the forum.
