You are here

General discussion

Topic / Topic starter Replies Last postsort descending
Hot topic 150KW VESC
by paltatech » Sun, 2017-09-10 23:11
39
by paltatech
Fri, 2018-06-08 20:02
Normal topic [SOLVED]Motors "blocking totally" when throttling, after running VESC setup.
by MaddiQ » Tue, 2018-06-12 21:01
0
by MaddiQ
Tue, 2018-06-12 23:36
Normal topic VESC Error "No firmware response"
by Magoroth » Tue, 2018-06-12 15:41
1
by hexakopter
Wed, 2018-06-13 01:12
Normal topic 360 Rotation Hall Sensors, would these work through ADC?
by portnawake » Thu, 2018-06-07 02:37
3
by Roger Wolff
Fri, 2018-06-15 08:50
Normal topic Newby RPM question
by dirkske » Mon, 2018-06-18 23:00
7
by dirkske
Wed, 2018-06-20 20:45
Normal topic VESC Hardware link broken
by jparadie » Mon, 2018-06-18 12:21
1
by frank
Fri, 2018-06-22 11:33
Normal topic Raptor 2
by Phill Dixon » Wed, 2018-06-13 18:07
1
by frank
Fri, 2018-06-22 11:35
Normal topic Vesc tool won't connect vesc to motor
by moza1313 » Sat, 2018-06-16 10:25
2
by frank
Tue, 2018-06-26 08:48
Normal topic Motor only running in reverse
by obex_mike » Mon, 2018-06-25 16:25
2
by frank
Tue, 2018-06-26 12:36
Normal topic VESC with Raspberry Pi 3
by Antonio Rodrígu... » Sun, 2018-06-03 18:54
9
by ShortCircuit
Thu, 2018-06-28 15:33
Normal topic can't communicate with arduino nrf
by m.juan » Mon, 2018-07-02 16:57
0
by m.juan
Mon, 2018-07-02 16:57
Normal topic Cruise control by setting RPM over UART
by solidgeek » Thu, 2018-02-15 10:56
3
by Lzx19961014
Thu, 2018-07-05 11:20
Normal topic Overheat
by Phill Dixon » Tue, 2018-07-03 19:07
1
by frank
Tue, 2018-07-10 09:51
Normal topic FW Vesc-Tool V0.95
by Meche » Mon, 2018-07-09 21:07
1
by Meche
Wed, 2018-07-11 16:29
Normal topic Updating fw
by Phill Dixon » Fri, 2018-07-06 19:30
1
by frank
Fri, 2018-07-13 13:19
Normal topic Programming NRF51822 Module with ST-Link v2
by koralle » Wed, 2018-07-11 12:06
3
by koralle
Sun, 2018-07-15 01:28
Normal topic Failure of FOC mode brake
by jzy1115 » Sun, 2018-03-25 10:23
8
by iscle
Sun, 2018-07-15 19:19
Normal topic I have soldered MPU 9150 onto my ESC - How can I confirm that it is working?
by delond » Sat, 2018-07-14 15:05
2
by lock
Tue, 2018-07-17 02:26
Normal topic Question to get a new Motor Running
by speedy » Fri, 2018-07-20 07:59
1
by frank
Fri, 2018-07-20 10:23
Normal topic Problem- Regen tripping out BMS on battery pack
by jasontwd » Sun, 2018-07-29 10:10
2
by jzy1115
Tue, 2018-07-31 06:11
Normal topic Request: Report hall sensor tables.
by Roger Wolff » Thu, 2018-05-17 15:28
7
by Tilman Baumann
Mon, 2018-08-06 12:24
Normal topic Acceleration control to desired RPM
by bjohns » Fri, 2018-07-20 22:08
9
by arvidb
Thu, 2018-08-09 21:15
Normal topic Hub motor FOC detection.
by Roger Wolff » Tue, 2018-08-21 19:12
0
by Roger Wolff
Tue, 2018-08-21 19:12
Normal topic VESC Software Understanding
by shubhamt » Wed, 2018-08-22 15:40
0
by shubhamt
Wed, 2018-08-22 15:40
Normal topic Set McConf with no values --> bootloader erased?
by Kakskiv » Tue, 2017-11-28 12:52
3
by basti30
Wed, 2018-08-22 22:22
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - General discussion