You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Is it normal to have5th harmonic current ? by Alex Marques » Fri, 2023-02-10 16:01 |
0 |
by Alex Marques Fri, 2023-02-10 16:02 |
|
|
VESC on Chromebook? by Boa1277 » Sun, 2021-02-21 20:49 |
0 |
by Boa1277 Sun, 2021-02-21 20:49 |
|
|
Brake Button Gradual Braking by hackish » Thu, 2019-09-05 16:56 |
0 |
by hackish Thu, 2019-09-05 16:56 |
|
|
Improper feedback from VESC Hardware with low speed ( SensorlessBEMF ) by Pranit Bhamare » Tue, 2023-02-14 07:19 |
0 |
by Pranit Bhamare Tue, 2023-02-14 07:19 |
|
|
Help needed please by Mark griffin » Tue, 2022-12-13 14:51 |
0 |
by Mark griffin Tue, 2022-12-13 14:51 |
|
|
anti theft possible? by hummina » Tue, 2021-02-23 07:44 |
0 |
by hummina Tue, 2021-02-23 07:44 |
|
|
Using Hall as encoder input by Offline » Tue, 2021-01-19 10:41 |
0 |
by Offline Mon, 2021-02-08 10:19 |
|
|
FOC settings are working in one VESC hardware and not in another VESC hardware with same hardware version ( VESC 6MKVI ) by Pranit Bhamare » Fri, 2023-02-17 07:17 |
0 |
by Pranit Bhamare Fri, 2023-02-17 07:17 |
|
|
display readings by FatsoBatso » Wed, 2021-02-24 18:01 |
0 |
by FatsoBatso Wed, 2021-02-24 18:01 |
|
|
Impact of motor resistance value vs temperature by Torbjorn » Fri, 2022-12-16 09:09 |
0 |
by Torbjorn Fri, 2022-12-16 09:09 |
|
|
Weird BLDC Current Waveform by thepcman » Thu, 2019-07-25 10:38 |
0 |
by thepcman Thu, 2019-07-25 10:41 |
|
|
Simultaneous control of two BLDC motors with VESCs via CAN bus without RC controller by sampatsr » Mon, 2023-02-27 20:21 |
0 |
by sampatsr Mon, 2023-02-27 20:21 |
|
|
Need help with brushed fc 24 bolt motor control by searth » Sun, 2022-12-18 16:05 |
0 |
by searth Sun, 2022-12-18 16:05 |
|
|
Sensored mode studering by dtmpro621 » Thu, 2023-03-02 04:40 |
0 |
by dtmpro621 Thu, 2023-03-02 05:25 |
|
|
Recommended method for CAN Bus communication for 3 VESC by sivanhere » Sun, 2023-01-01 12:09 |
0 |
by sivanhere Sun, 2023-01-01 12:09 |
|
|
Step/Dir signals by wall0069 » Sun, 2019-06-09 16:06 |
0 |
by wall0069 Sun, 2019-06-09 16:06 |
|
|
How to set a jog speed using an encoder by AK6302019 » Wed, 2019-08-07 15:42 |
0 |
by AK6302019 Wed, 2019-08-07 15:42 |
|
|
Reverse ADC and UART by ben_src » Mon, 2019-08-12 17:22 |
0 |
by ben_src Mon, 2019-08-12 17:22 |
|
|
Any way to increase detection time? by VapeGod » Wed, 2023-01-25 05:58 |
0 |
by VapeGod Wed, 2023-01-25 05:58 |
|
|
Where to find CAN protocol documentation? by doctarr » Tue, 2020-12-29 15:33 |
0 |
by doctarr Tue, 2020-12-29 15:33 |
|
|
Vesc to Uart (Nextion display) by g1tana » Mon, 2019-08-19 15:29 |
0 |
by g1tana Mon, 2019-08-19 15:30 |
|
|
Flipsky 4.20 plus with VX1 pro remote by Tropicalstorm » Tue, 2023-01-31 21:30 |
0 |
by Tropicalstorm Tue, 2023-01-31 21:30 |
|
|
motor stuttering and having a hard time with receiver ... help by okyuubix » Tue, 2021-09-14 23:43 |
0 |
by okyuubix Tue, 2021-09-14 23:49 |
|
|
vesc6 limitations by badger1666 » Sat, 2018-04-28 19:20 |
0 |
by badger1666 Sat, 2018-04-28 19:20 |
|
|
VESC cutout using smart reverse by Brokepilot » Thu, 2024-04-25 16:50 |
0 |
by Brokepilot Thu, 2024-04-25 16:50 |
Log in to post new content in the forum.
