You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Something about encoder connection by ztwsa007 » Mon, 2019-07-01 13:43 |
1 |
by ztwsa007 Fri, 2019-07-05 03:26 |
|
|
Problems with 100% throttle input by levin » Wed, 2023-11-08 08:32 |
1 |
by Frizzaper Tue, 2023-12-12 07:48 |
|
|
Overcome the deadband torque at low rpm by shulnak » Sun, 2023-07-30 22:48 |
1 |
by userk_88_vanto Fri, 2023-09-15 15:34 |
|
|
Vesc6MK3 stops responding to throttle input by idlebear » Fri, 2023-11-17 17:41 |
1 |
by idlebear Fri, 2023-12-29 22:44 |
|
|
BT module and UART remote simultaneously on dual vescs by Rc 44 » Fri, 2023-12-01 18:40 |
1 |
by Rc 44 Mon, 2024-01-08 04:48 |
|
|
Could not read motor configuration during detection by siegele1 » Wed, 2023-08-02 17:17 |
1 |
by electricfox Thu, 2023-08-03 08:23 |
|
|
Flipsky 75200 Pro V2.0 by sweendog311 » Fri, 2023-12-08 20:12 |
1 |
by moose09876 Thu, 2024-01-04 15:18 |
|
|
Get values from slave VESC by Snabelost » Mon, 2023-08-07 08:54 |
1 |
by Snabelost Mon, 2023-08-07 13:21 |
|
|
VESCs rotating the motors at constant RPM on UART control by Pratham701 » Tue, 2021-07-13 10:49 |
1 |
by Indy8976 Wed, 2022-08-24 11:27 |
|
|
Using a AD2S1205 RTD converter by derekrose » Tue, 2023-12-12 22:36 |
1 |
by Brainiac Tue, 2023-12-26 11:56 |
|
|
Battery/Motor Current on VESC Tool is less than Actuals by gowrav » Thu, 2021-07-15 13:27 |
1 |
by skyline1970 Sat, 2021-09-18 11:44 |
|
|
VESC first build questions by evbkez » Fri, 2019-08-02 14:58 |
1 |
by TittyTwister Sun, 2022-07-10 21:35 |
|
|
anybody interested in ninebot-segway's sensorless position observer? by lanmanck » Mon, 2020-06-01 04:33 |
1 |
by lanmanck Wed, 2020-06-03 02:57 |
|
|
How I control the RPM of my motor from VESC with Arduino? by George W. » Sat, 2020-04-25 16:10 |
1 |
by frank Thu, 2020-04-30 18:16 |
|
|
Control of 4000w bldc motor with hall effect sensors by Abdullah Ajmal » Sat, 2022-04-16 10:14 |
1 |
by frank Sat, 2022-04-16 20:01 |
|
|
Dual controller: turn left and right by coolic » Tue, 2025-02-25 13:01 |
1 |
by electricfox Thu, 2025-02-27 07:05 |
|
|
Forum GUI by parasole » Fri, 2017-11-10 09:25 |
1 |
by VJPANDI Thu, 2022-11-10 15:07 |
|
|
Torque Ramp Rate whilst in FOC by J_W97 » Mon, 2022-03-14 11:50 |
1 |
by skyline1970 Mon, 2022-03-14 20:29 |
|
|
PPM Configuration in VESC Tool by yourpals » Sun, 2020-06-07 21:33 |
1 |
by thefallen Mon, 2020-06-08 16:21 |
|
|
22 pole motor and potentiometer throttle by Kenneth » Mon, 2020-04-27 23:01 |
1 |
by Kenneth Tue, 2020-04-28 08:59 |
|
|
Wrong software shows up. Answered my own question. by leecon » Fri, 2025-03-07 17:50 |
1 |
by leecon Tue, 2025-03-11 17:00 |
|
|
Same MC Values, differnet Output on Dual Setup by E-Toxx » Mon, 2017-09-11 09:27 |
1 |
by Necromenz Mon, 2017-09-11 21:08 |
|
|
[SOLVED] COMM_GET_VALUES on top of COMM_FORWARD_CAN not working by yes_wecangogreen » Sun, 2025-03-09 12:48 |
1 |
by yes_wecangogreen Wed, 2025-03-12 10:22 |
|
|
Vesc antispark always active by axelSSS » Wed, 2025-06-18 19:44 |
1 |
by tokerodev Fri, 2025-07-04 21:47 |
|
|
Bluetooth LE not working with Vesc Tool 3.01 by Gatze » Fri, 2022-04-22 19:31 |
1 |
by frank Thu, 2022-05-12 09:14 |
Log in to post new content in the forum.
