You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
. by faheemift » Tue, 2021-03-30 15:37 |
0 |
by faheemift Thu, 2021-04-01 13:58 |
|
|
information to drive 400kv drone motor on ClosedLoop with AS5047 by Syl2078 » Sun, 2019-02-17 19:20 |
0 |
by Syl2078 Sun, 2019-02-17 19:20 |
|
|
BLDC zero cross happens too early by Sgw32 » Thu, 2021-05-20 19:10 |
0 |
by Sgw32 Thu, 2021-05-20 19:10 |
|
|
Newer DRV8353RS instead of DRV8301? by whydoilive » Fri, 2021-04-02 10:24 |
0 |
by whydoilive Fri, 2021-04-02 10:24 |
|
|
Motor switch off moving on at 10°C by sirAnton » Sun, 2021-04-04 10:55 |
0 |
by sirAnton Sun, 2021-04-04 10:55 |
|
|
Current sensor and commanded current by galp » Fri, 2019-02-22 23:08 |
0 |
by galp Fri, 2019-02-22 23:08 |
|
|
Interfacing with the VESC using UART by dhruvna » Thu, 2023-03-16 17:42 |
0 |
by dhruvna Thu, 2023-03-16 17:42 |
|
|
When I mount the propeller on the motor ,I get a new promblem by moto_guy » Sat, 2019-03-02 05:16 |
0 |
by moto_guy Sat, 2019-03-02 05:16 |
|
|
ScholarOn by kelly edwards » Thu, 2021-03-11 10:54 |
0 |
by kelly edwards Thu, 2021-03-11 10:54 |
|
|
Help Please 🥺 by Jou2023 » Sun, 2023-05-28 17:58 |
0 |
by Jou2023 Sun, 2023-05-28 17:58 |
|
|
Configuration of underwater thruster by UnderwaterMotors » Fri, 2023-03-24 18:10 |
0 |
by UnderwaterMotors Fri, 2023-03-24 18:10 |
|
|
how do you arm your Vesc in arduino code? by the creator » Wed, 2019-03-13 01:11 |
0 |
by the creator Wed, 2019-03-13 01:33 |
|
|
Vesc 75100 by Matteo Christian » Wed, 2023-05-31 13:32 |
0 |
by Matteo Christian Fri, 2023-06-09 12:08 |
|
|
Dual VESC via CAN by scholtylicious » Sat, 2021-03-13 15:56 |
0 |
by scholtylicious Sat, 2021-03-13 15:56 |
|
|
Using Motor hall sensors as the encoder by Russ g » Wed, 2019-05-08 16:01 |
0 |
by Russ g Wed, 2019-05-08 16:01 |
|
|
DRV8323 by Jessica » Thu, 2019-03-14 11:41 |
0 |
by Jessica Thu, 2019-03-14 11:42 |
|
|
Need help maximizing torque at low RPM - FOC, Hub motors, Flipsky VESC 4.12 50A by Bruce » Mon, 2021-03-15 03:31 |
0 |
by Bruce Mon, 2021-03-15 03:31 |
|
|
VESC appears to loose sync when increasing throttle by srinath » Sun, 2023-06-04 04:11 |
0 |
by srinath Sun, 2023-06-04 04:11 |
|
|
Changing the timer for VESC auto turn off timing by dsuresh » Mon, 2021-03-15 21:19 |
0 |
by dsuresh Mon, 2021-03-15 21:19 |
|
|
No load FOC stops when full FWD throttle. by toboli » Mon, 2023-06-05 18:41 |
0 |
by toboli Mon, 2023-06-05 18:41 |
|
|
RPM and torque control modes by srinath » Fri, 2023-06-16 10:52 |
0 |
by srinath Fri, 2023-06-16 10:54 |
|
|
STM32F407 by john » Wed, 2019-03-27 13:40 |
0 |
by john Wed, 2019-03-27 13:40 |
|
|
Error code 6 by PatWhite32 » Mon, 2023-06-19 23:15 |
0 |
by PatWhite32 Mon, 2023-06-19 23:15 |
|
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 » Wed, 2023-04-12 16:28 |
0 |
by Tom65 Wed, 2023-04-12 16:28 |
|
|
current measurements crazy high after replacing DRV8301 with DRV8302, it throws a FAULT_CODE_ABS_OVER_CURRENT by idkanythinggoes » Thu, 2021-03-18 04:34 |
0 |
by idkanythinggoes Thu, 2021-03-18 04:34 |
Log in to post new content in the forum.
