You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Sound when braking and Accelerating by Paul15578 » Wed, 2018-01-03 10:04 |
11 |
by frank Thu, 2018-12-06 10:22 |
|
|
Rough Motor Running When USB Cable At Vesc Tool is Disconnected by David Cunliffe » Sun, 2022-01-16 11:42 |
11 |
by David Cunliffe Sun, 2022-01-16 15:32 |
|
|
VESC75/300 pre-order, limited volume by frank » Fri, 2018-11-23 10:06 |
11 |
by benjamin Mon, 2018-12-10 08:19 |
|
|
ADC EBike Throttle Not Responding by d_hoody » Thu, 2018-12-13 02:04 |
11 |
by Oded Mazor Sat, 2022-02-19 07:41 |
|
|
FRF measurement functionality by Elwin » Sun, 2021-10-31 01:06 |
11 |
by Elwin Sat, 2021-11-06 22:05 |
|
|
Does VESC reduce/disable regen braking based on battery voltage? by rorosaurus » Tue, 2020-08-11 23:20 |
11 |
by J_W97 Mon, 2022-03-14 14:43 |
|
|
FOC and extremely low speeds do not look sinusoidal by wdaehn » Wed, 2017-11-29 21:33 |
11 |
by Benjamin Mahony Wed, 2018-01-10 01:19 |
|
|
Best way to stop "de-sync" of motors by Paul15578 » Tue, 2017-12-05 04:57 |
11 |
by Dillon Mon, 2018-11-19 02:11 |
|
|
VESC 6 Hall Sensor Issues by josh » Mon, 2017-10-02 01:57 |
11 |
by Kent Tabor Fri, 2020-11-13 14:00 |
|
|
High speed braking failure by danspratt » Wed, 2020-07-22 23:58 |
11 |
by knuthcomi Sat, 2021-03-06 23:48 |
|
|
Encoder connection by Herbie » Fri, 2019-05-31 15:12 |
11 |
by Dencio1976 Fri, 2022-10-21 13:46 |
|
|
Knocking inside motor between 10-20km, after and before all is ok by spacewalker » Mon, 2021-05-10 11:00 |
11 |
by Fpvlee Thu, 2021-07-29 15:30 |
|
|
Questions about encoder on FSesc 6 by willyfan » Wed, 2018-08-29 20:30 |
11 |
by Vedderfanboy Tue, 2023-01-17 13:17 |
|
|
Strange HFI results by Ebike_Ninja » Thu, 2020-01-30 01:06 |
11 |
by joekeo Fri, 2020-10-23 11:49 |
|
|
Switching frequency factor 2 lower by Elwin » Sat, 2021-11-13 22:48 |
10 |
by Elwin Sun, 2022-01-09 08:31 |
|
|
Brakes completely repeatedly failing at high temperature by Paul15578 » Mon, 2018-03-26 13:06 |
10 |
by Paul15578 Sun, 2018-04-22 14:16 |
|
|
Noised signal from motor NTC sensor | HW4.12 FW3.27 by ma-j-sterelektron » Wed, 2017-09-06 18:41 |
10 |
by vescsci Wed, 2020-07-15 22:47 |
|
|
Dual VESC, Dual UART? by kneave » Mon, 2020-08-17 22:00 |
10 |
by Duane Degn Mon, 2020-08-24 00:23 |
|
|
about reference hardware by qdxiatao » Mon, 2017-09-25 08:32 |
10 |
by lizardmech Tue, 2017-11-21 19:40 |
|
|
FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 by TB_Poule » Sat, 2021-04-10 17:26 |
10 |
by Mohanangappan Wed, 2024-09-18 16:20 |
|
|
Suddenly broken by moto_guy » Fri, 2019-03-08 13:50 |
10 |
by David_1 Fri, 2022-06-17 21:07 |
|
|
VESC Questions from the newbie by mendez » Fri, 2019-02-08 21:13 |
10 |
by frank Mon, 2019-02-18 08:52 |
|
|
FOC current oscillation at max. speed by ProgramThyself » Mon, 2020-08-10 05:55 |
10 |
by SRFirefox Wed, 2020-08-26 23:10 |
|
|
VESC with auto calibration of grace one motor (videos included) by ligi » Mon, 2020-10-19 02:13 |
10 |
by ligi Tue, 2020-11-17 06:56 |
|
|
Solved: Cruise Control: Push to Activate; Cancel on BRK or Throttle Touched by vadicus » Wed, 2020-01-08 23:47 |
10 |
by vadicus Sat, 2024-02-17 01:37 |
Log in to post new content in the forum.
