You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
FSESC 75100 motor problem by anythingstl » Tue, 2024-02-13 17:15 |
0 |
by anythingstl Mon, 2024-02-19 19:23 |
|
|
VESC custom firmware custom UART message by steveyplst » Tue, 2020-08-04 10:23 |
0 |
by steveyplst Tue, 2020-08-04 10:23 |
|
|
Flipsky FSV 6.6 no longer working with new VESC Tool by oliver1998 » Fri, 2025-09-12 06:06 |
0 |
by oliver1998 Fri, 2025-09-12 06:06 |
|
|
Dual VESC Controller - Internal CAN Forwarding Failure -NOW WITH CODE EXAMPLE ;) by XAQ » Mon, 2025-09-15 07:52 |
0 |
by XAQ Mon, 2025-09-15 17:42 |
|
|
2 Speed ADC control by totalgeek9224 » Mon, 2025-09-22 19:47 |
0 |
by totalgeek9224 Mon, 2025-09-22 19:47 |
|
|
VESC specialist required. by BlackPanthera » Mon, 2022-07-18 17:11 |
0 |
by BlackPanthera Mon, 2022-07-18 17:11 |
|
|
connecting vesc tool with Prototipo by Govert » Thu, 2020-07-02 19:43 |
0 |
by Govert Thu, 2020-07-02 19:43 |
|
|
How do you turn on traction control ( I can't remember) by msim2 » Fri, 2022-05-20 22:06 |
0 |
by msim2 Fri, 2022-05-20 22:06 |
|
|
VESC 6 Mark III and Traxxas Summit Radio Receiver PWM / PPM Signals by j98221@gmail.com » Fri, 2020-07-03 07:27 |
0 |
by j98221@gmail.com Fri, 2020-07-03 07:27 |
|
|
Problem with Android app by Er-Chispa » Wed, 2025-10-08 20:58 |
0 |
by Er-Chispa Wed, 2025-10-08 21:02 |
|
|
My VESC TOOL did not have "balance" by Elijah K » Wed, 2020-08-12 07:52 |
0 |
by Elijah K Wed, 2020-08-12 07:53 |
|
|
About How to control the "FLIPSKY Dual FSESC6.7 PLUS" by tonyH » Tue, 2025-10-14 11:35 |
0 |
by tonyH Tue, 2025-10-14 11:35 |
|
|
ADC input protection proposal by arestechfinland » Mon, 2020-07-06 19:41 |
0 |
by arestechfinland Mon, 2020-07-06 19:41 |
|
|
VESC with asynchronous motors by afbbfa » Fri, 2022-07-29 22:51 |
0 |
by afbbfa Fri, 2022-07-29 22:51 |
|
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse » Fri, 2022-06-03 08:13 |
0 |
by notahorse Fri, 2022-06-03 08:13 |
|
|
Regenerative braking in scooter Zero x11 72V dual motor 2 x 1600 w peak power 6000W by Makroman » Wed, 2020-07-08 20:00 |
0 |
by Makroman Wed, 2020-07-08 20:00 |
|
|
Hall sensor port repeatedly fried on original hardware by Rc 44 » Fri, 2025-10-24 22:44 |
0 |
by Rc 44 Fri, 2025-10-24 22:44 |
|
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 » Mon, 2022-08-01 18:08 |
0 |
by moose09876 Mon, 2022-08-01 18:08 |
|
|
VESC as generator - settings confirmation by justinlsquire » Mon, 2022-06-06 02:44 |
0 |
by justinlsquire Mon, 2022-06-06 02:44 |
|
|
VESC to spin motor after power up? by A_Baum92881 » Fri, 2025-10-31 06:01 |
0 |
by A_Baum92881 Fri, 2025-10-31 17:21 |
|
|
VESC Tool Android pairinglist reset with metr.at by nice2cu » Sun, 2020-08-23 12:24 |
0 |
by nice2cu Sun, 2020-08-23 12:24 |
|
|
FOC vs. BLDC by CTSchorsch » Wed, 2020-07-15 13:15 |
0 |
by CTSchorsch Wed, 2020-07-15 13:15 |
|
|
Vesc Orientation Python by flomai28 » Mon, 2025-11-10 09:44 |
0 |
by flomai28 Mon, 2025-11-10 09:44 |
|
|
Could use some help tuning for low speed by Berrie » Tue, 2025-07-15 20:24 |
0 |
by Berrie Tue, 2025-07-15 20:24 |
|
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset » Thu, 2022-08-04 01:44 |
0 |
by liminalsunset Thu, 2022-08-04 01:44 |
Log in to post new content in the forum.
