You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC FOC detecting running flawlessly, motor flipping direction erratically when running in speed and duty mode by DMKitsch » Fri, 2020-10-23 21:59 |
5 |
by milesf Wed, 2020-11-18 06:01 |
|
|
Pwm+dir input support by adilrepas » Tue, 2020-12-22 03:32 |
5 |
by skyline1970 Sat, 2021-02-06 19:32 |
|
|
VESC Classic 100V shutting down by floh349 » Thu, 2026-08-27 13:44 |
5 |
by floh349 Thu, 2026-10-15 18:26 |
|
|
VESC TOOL ADC Voltage mapping too low. SOLVED by Ecyclist » Fri, 2018-10-19 22:38 |
5 |
by sam.vanratt Thu, 2018-11-22 20:21 |
|
|
Hall Sensors Not Detected by leymane » Fri, 2023-08-18 17:12 |
4 |
by Ben26 Mon, 2024-10-21 22:45 |
|
|
Trampa VESC6 USB connectivity problem caused by usb hub? by hagoston » Tue, 2021-06-01 10:27 |
4 |
by hagoston Wed, 2021-06-02 09:27 |
|
|
FOC VESC for QS Motor 205 50H 3000w by karlisakis » Mon, 2021-06-07 21:29 |
4 |
by vadicus Mon, 2021-10-25 19:39 |
|
|
Wand speed display incorrect - Solved by hans_maier » Sat, 2019-09-14 15:16 |
4 |
by hans_maier Wed, 2019-09-18 22:31 |
|
|
Driver explosion by fer-bo » Mon, 2021-07-05 11:48 |
4 |
by fer-bo Wed, 2021-07-07 14:50 |
|
|
Two phase modulation by jguy » Sat, 2023-12-09 13:33 |
4 |
by jguy Fri, 2023-12-15 11:49 |
|
|
Nothing works for MY1020 3kw 72v motor and flipsky75100 by Valérian Pigeon » Tue, 2025-02-04 16:49 |
4 |
by Valérian Pigeon Thu, 2025-02-06 20:59 |
|
|
Burned my VESC 6 MKV. Wrong polarity by okhsunrog » Thu, 2022-04-07 01:44 |
4 |
by frank Thu, 2022-04-07 10:27 |
|
|
Flipsky 75/100 Mosfet short? by Michael Campbell » Mon, 2022-04-11 08:29 |
4 |
by Michael Campbell Tue, 2022-04-12 00:03 |
|
|
FOC : Stop Motor without Active Brake by Flyingtux » Mon, 2022-03-14 12:35 |
4 |
by Flyingtux Tue, 2022-03-15 23:09 |
|
|
Improved low speed and full stop control with Hall by pf26 » Mon, 2020-06-08 19:33 |
4 |
by pf26 Tue, 2020-09-22 17:34 |
|
|
Using vesc for Position and driving my BB8 Robot by Quicksilverstar » Wed, 2017-11-15 19:25 |
4 |
by Quicksilverstar Sat, 2017-11-25 16:11 |
|
|
program motorstop for VTOL by Jan-Willem » Wed, 2020-04-29 18:55 |
4 |
by frank Thu, 2020-04-30 18:08 |
|
|
Sudden drop in speed after releasing throttle in FW mode by shokrabi » Sat, 2022-04-23 15:05 |
4 |
by DeuceDos Tue, 2023-05-30 09:54 |
|
|
Positional Control, Hall Sensor by wdaehn » Fri, 2017-12-08 15:02 |
4 |
by wdaehn Mon, 2017-12-25 09:46 |
|
|
Full Throttle direct after input deadband by toerde » Sat, 2022-04-30 18:54 |
4 |
by frank Mon, 2022-05-09 08:22 |
|
|
Problem with regenerative breaking by ligi » Sat, 2022-04-02 15:08 |
4 |
by ligi Sat, 2023-07-15 02:02 |
|
|
Control singular VESC using CAN-BUS and Arduino by Cam » Wed, 2021-01-06 10:29 |
4 |
by craiggault Wed, 2022-04-27 23:07 |
|
|
ADC1 problems with Firmware/Hardware issue? by sam.vanratt » Thu, 2018-12-27 22:31 |
4 |
by sam.vanratt Thu, 2019-01-03 17:46 |
|
|
Stall torque in sensorless mode by cromoly » Sun, 2018-11-25 07:54 |
4 |
by spork Thu, 2018-11-29 03:23 |
|
|
vesc6 help with hub motor by badger1666 » Thu, 2018-12-20 18:36 |
4 |
by badger1666 Fri, 2018-12-21 06:03 |
Log in to post new content in the forum.